background image

20

CAUTION: Oil must be added to the hydraulic reservoir and the engine before 

starting or operation.

Step 1

Please add approximately 15/20 litres of hydraulic fluid. The remaining hydraulic fluid will be added 

after the cylinder is cycled� AW46 hydraulic oil is recommended� Use only clean oil and take care to 

prevent dirt from entering the hydraulic reservoir�

ENGINE OIL RECOMMENDATIONS

Use 4 stroke automotive detergent oil� SAE30 is recommended for general use� Refer to the SAE 

Viscosity Grades chart in your engine owner’s manual for average temperature ranges. The engine 

oil capacity is 600ml for the Briggs & Stratton 6.5hp (30 ton), 1.1lts for the Briggs & Stratton 10hp (35 

ton) and 1.1lts for the Briggs & Stratton 13.5hp (40 ton). Always check oil level before starting the 

engine and keep level full�

DANGER

CAUTION

WARNING: Read and understand the complete operation manual before 

assembling or using this product! Failure to comprehend and comply with 

warnings, cautions and instructions for assembly and operation could result in 

serious injury or death.

DO NOT permit children to operate this equipment at any time� DO NOT permit 

others that have not read and understood the complete operation manual to operate 

this equipment� Operation of power equipment can be dangerous� It is the sole 

responsibility of the operator to understand the assembly and safe operation of this 

product�

Step 2

After the hydraulic reservoir and the engine crankcase are filled with oil, start the engine. The 

hydraulic pump is self-priming� With the engine running, move the hydraulic valve lever toward

the foot plate� This will cause the cylinder to extend and expel air� When the cylinder is fully extended, 

retract it� Repeat this procedure several times� An erratic movement of the cylinder indicates that

there is still air in the system. Add about 3 to 6 litres of hydraulic fluid. Approximately 19 litres will 

register just above the top fill line on the dip stick. The total capacity of the entire hydraulic system is 

30 litres, with 19 litres of hydraulic fluid minimum to operate.

NOTE: If the tank is overfilled it will expel oil from the breather cap when the cylinder is 

retracted. Cycle the cylinder again until it has a constant speed which indicates that all air has 

been expelled.

Operating Instructions

Содержание BWMLS30





























Отзывы: