background image

BVM ® 2019 

 11/12/2019 

INTRODUCTION 

Thank you for purchasing the Go Fly Ultra Bandit Evo. This model represents the latest in 
manufacturing  technology  and  completion  for  the  R/C  jet  enthusiast.  The  factory  has 
expertly crafted and thoroughly inspected all aspects of the model. Only a small amount of 
work is required to complete the assembly of your Bandit Evo. 
 
This manual contains instructions for safety, operation and maintenance. It is essential to 
read and follow all of the instructions and warnings in the manual. 

 

Please  read  the  entire  manual  to  become  familiar  with  the  processes  and  procedures 
before you begin to assemble your aircraft. 

Disclaimer 

Bob Violett  Models Inc.  assumes no  liability  for  the  operation  and  use of  these  products. 
The  owner  and  operator  of  these  products  should  have  the  necessary  experience  and 
exercise  common  sense.  Said  owner  and operator must  have a  valid  Academy  of  Model 
Aeronautics license and a “Turbine Waiver” for operation in the U.S.A. 
 
This  is  a  sophisticated  jet  model  aircraft.  It  must  be  operated  with  caution  and  common 
sense and requires some basic mechanical ability. Failure to operate this product in a safe 
and responsible manner could result in injury or damage to the product or other property.  
 

Notice:

 Do not use with incompatible components or alter this product in any way outside 

of  the  instructions  provided  by  BVM,  Inc.  The  BVM  Ultra  Bandit  Evo  has  been  designed 
and flight tested around  160-200N class engines. Damage to the aircraft may result from 
exceeding this thrust limitation. 

 

List of BVM supplied items 

 

Assembly and Operating Manual Package 

 

Flush Mount Vent Fitting 

 

 

 

(#PS-SP-0301) 

 

Central Controller Instructions 

Recommended Accessories 

You may have some of these products in your shop, but if not, refer to this list. 

 

160 to 200N engine of your choice. 

 

BVM HI FLOW U.A.T.  

 

 

 

(BVM# TA-SR-1001) 

 

BVM Over Flow Tank   

 

 

 

(BVM# 6047) 

 

12 Channel Power Safe Receiver 

 

 

(2) 7.4v Batteries 3600 mAh RX 

 

Safety Wire    

 

 

 

 

(BVM# 2800) 

 

Bavarian Demon Aero Cortex Pro Gyro  

 

(#V-DA-BD-Cortex Pro) 

 

ULTRA BANDIT Jet Foam Cradle 

 

 

(#K7300-65) 

 

 
 
 
 
 
 
 

Safety Wire 

Содержание GO FLY GOLD
























Отзывы: