BVM Go Fly Gold F-18C Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 34

BVM Go Fly Gold F-18C Скачать руководство пользователя страница 11

BVM ®2021 10 10/2021

CANOPY AND SERVO INSTALLATION



When satisfied with everything inside you

can put the servo / canopy mount back in the
model with the 7 screws you took out before.
There will also be a servo lead to plug in that
controls the canopy.

NOTE:

A small drop of Thin CA in the holes will

make for a nice tight screw fit.
Repeat for all 7.

CANOPY FRAME INSTALLATION



Like before, this is a bit tricky. Just take your time during this step. Take the small pieces

of tubing that are circled in the photo and slide them towards the middle of the rod. Then
place the canopy on the model and with the rod in the other hand reach inside the model
and put the rod back into the canopy mount one side at a time. After that is complete take
the small pieces of tubing and push them back out till they contact to the inside of the
canopy mount.

NOTE:

The canopy does pivot as well as slide up and down in the back.

«
...
9
10
11
12
13
...
»

Содержание Go Fly Gold F-18C



































Отзывы:

Нет отзывов