Bustec ProDAQ 3424 Скачать руководство пользователя страница 45

Страница: 45 / 56

ProDAQ 3424 Function Card User Manual

3424-XX-UM



1998-2005 Bustec Production Ltd.

Page 45 of 56

This bit selects between edge or level mode of the Analog Trigger.

0 : edge mode selected
1 : level mode selected

USAGE



The direction or condition of the trigger is selected using COMP_SEL

3:1

ATCHN_ADDR

– Analog Trigger Channel Address

These bits specify a channel the AT_THR1/2 will be applied to.

000 : card channel 1

001 : card channel 2

010 : card channel 3

011 : card channel 4

100 : card channel 5

101 : card channel 6

110 : card channel 7
111 : card channel 8

USAGE



Only one Analog Trigger channel can be enabled at the time.

AT_UPD

– Analog Trigger Update

This bit, when set, lunches the update of the Analog Trigger settings.

0 : update not launched
1 : update of the Analog Trigger launched

USAGE



Any write with AT_UPD bit set changes previous settings



If AT_UPD bit is cleared the write can still change THR2[11:4] bits

All Analog Trigger settings, except of the THR1 and THR2, can be updated only if AT_UPD bit is
set during write to the register. THR1 and THR2 can be changed independently of the AT_UPD bit
settings.

5.16. CHNxCFG

– Channel x Configuration Register

These are registers used to configure front-

end of channel ‘x ‘, where ‘x’ is in the range from 1 to 8.

Bit

Access &

Default

Description

15:12

Reserved

11:10

R/W

‘00’

GAIN2_SEL

– Gain of the Second Stage Selection

These bits select the gain of the second PGA in the signal path.

00 : x1 gain
01 : x10 gain
10 : x100 gain
11 : not allowed

USAGE



Channel’s gain is defined as GAIN1 * GAIN2

9:8

R/W

‘00’

GAIN1_SEL

– Gain of the First Stage Selection

These bits select the gain of the first PGA in the signal path.

00 : x1 gain
01 : x2 gain
10 : x5 gain
11 : x10 gain

USAGE



Channel’s gain is defined as GAIN1 * GAIN2

R/W

HPF_EN

– High Pass Filter Enable

This bit enables ADC’s built in high pass filter.

0 : High pass filter disabled
1 : High pass filter enabled

Содержание ProDAQ 3424
























































Результаты поиска

Содержание ProDAQ 3424

Отзывы:

Похожие инструкции для ProDAQ 3424

Бренды по названию

Популярные бренды

Bustec ProDAQ 3424, Руководство пользователя

Результаты поиска

Содержание ProDAQ 3424

Отзывы:

Похожие инструкции для ProDAQ 3424

Бренды по названию

Популярные бренды