background image

_

 5 

_

Assembly

Installing Shaft Assembly and Angle drive

Attach the shaft assembly to the hedge trimmer angle 

drive assembly.
NOTE:  Carefully inspect both side of the shaft assembly. 

The arrow marking side of the shaft assembly 

positions to the power unit. The no marking side 

of the shaft assembly connects to the angle drive 

assembly.

Insert the shaft assembly into the angle drive 

assembly whilerotating the driveshaft to engage 

the splines. Align the locating hole and install the 

locating screw through the side of the angle drive. 

Then tighten the clamping screw. If properly 

installed, rotating the end of the driveshaft will 

cause the cutting blades to move.

Shaft Assembly

Driveshaft

Arrow Mark

Locating Hole

Locating

Screw

Splined

Angle Drive

Clamping Screw

Attaching and Detaching for the Power 

Unit and the Shaft Assembly

Attaching

1  First, loosen the clamping knob before 

attaching the shaft assembly to the shaft cou-

pler. 

Note: Do not over loosen the clamping 

knob or it  may fall out.

2  Insert the shaft assembly to the shaft coupler 

with the positioning hole faced up as shown. 

Connect the both drive shafts completely in 

the matching position by moving the shaft 

assembly to forward and backward and left 

turn and right turn. When the shaft assembly 

is positioned correctly, spring tensioned posi-

tioning lever will be returned to the initial 

position.

3  Tighten the clamping knob firmly.

Clamping 

Knob

Shaft Coupler

Positioning 

Lever

Positioning Hole

Shaft 

Assembly

Positioning 

Lever

Positioning lever 

is lowered state

Positioning lever 

is raised state

Insert

Tighten

Loosen

Incorrect Assembled

Correct Assembled

Содержание MC-HTS-2

















Отзывы: