background image

OPERATING WITH FLOAT CONTROL 

During  hard  surface  operation,  keep  the  bucket  level 

and put the  lift lever  in  the  float  position to permit the 
bucket  to  float  on  the  working  surface.  If  hydraulic 
down  pressure  is  exerted  on  the  bucket,  it  will  wear 
faster than normal. 

The  float  position  will  also  prevent  the  mixing  of 
surface  material  with  stockpile  material.  The  float 
position  will  reduce  the  change  of  surface  gouging 
when  removing  snow  or  other  material,  or  when 
working with a blade. 

PEELING AND SCRAPING 

Use  down  pressure  and  a  slight  bucket  angle  to  start 

long  cuts.  Make  a  short  angle  cut  and  break  out 

cleanly. 

With  the  bucket  level,  start  a  cut  at  the  notch 
approximately  two  inches  deep.  Hold  the  depth  by 
feathering the bucket lever  to adjust  the  cutting lip  up 
or  down.  When  the  front  tires  enter  the  notch,  adjust 
the lift and bucket lever to maintain proper depth. 

2ndCut 

Make  additional  cuts  until  the  desired  depth  is 

reached. 

3rd Cut  4th Cut,  etc. 

During  peeling  operations,  use  lift  cylinder  down 

pressure  and  a  slight  bucket  angle  for  penetration  to 
the desired working depth.  After reaching  the  desired 
working  depth,  use  only  the  bucket  lever,  leaving  the 
lift  lever  in  either  the  float  or  neutral  position.  This 
allows  the  operator  to  control  the  bucket  angle  and 
maintain a precise cut. 

If  the  lever  is  used  without  controlling  the  bucket 

angle,  the bucket  will gouge and leave a  series of  ruts 
in the surface. 

BACKFILLING 

Approach the pile with a level bucket. When adjusting 
the cut to a load that the tractor can push,  actuate the 
lift lever and maintain a level bucket. 

Leave the soil in the bucket because dumping on each 

pass wastes time.  Lift and level the bucket for the next 
pass while backing from the excavation. 

Operate at  right  angles to the ditch.  Take  as big a  bite 
as the tractor can handle without lugging the engine. 

Leave the soil  which  drifts  over  the  side  of the bucket 

for final cleanup. 

Efficient  backfilling  occurs  when  the  tractor  pushes 

the  maximum  amount  of  soil  without  losing  speed  or 

traction.  If the  tractor  slows,  reduce  the width  of cut. 

If  the  tractor  is  not  working  at  capacity,  increase  the 

width of cut. 

When backfilling on a slope,  have the soil  piled on  the 
high side for easier backfilling. 

Содержание 2400 QT

























Отзывы:

Похожие инструкции для 2400 QT