BUSCH R5 ATEX Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 40

background image

3 | Transport

10 / 40

0870572240_RA0400-0630C_Ex_-0011_IM_en

3

Transport

WARNING

Suspended load.

Risk of severe injury!

• Do not walk, stand or work under suspended loads.

WARNING

Lifting the machine using the motor eye bolt.

Risk of severe injury!

• Do not lift the machine using the eye bolt fitted to the motor. Only lift the machine as

shown.

NOTICE

In case the machine is already filled with oil.

Tilting a machine that is already filled with oil can cause large quantities of oil to in-
gress into the cylinder. Starting the machine with excessive quantities of oil in the
cylinder will immediately break the vanes and ruin the machine!

• Drain the oil prior to every transport or always horizontally transport the machine.

• Make sure that the eyebolt(s) (EB) is/are in faultless condition, fully screwed in and

tightened by hand.

Machine weight:

see the technical data or the nameplate (NP)

• Check the machine for transport damage.

If the machine is secured to a base plate:

• Remove the machine from the base plate.

«
...
8
9
10
11
12
...
»

Содержание R5 ATEX









































Отзывы:

Нет отзывов

Похожие инструкции для R5 ATEX

Бренд: HISEER Страницы: 8

Бренд: Comet Страницы: 12

Бренд: Hi-Force Страницы: 16

Бренд: Ocean Aire Страницы: 36

Бренд: Xylem Страницы: 8

Бренд: Wacker Neuson Страницы: 60

CLI U12 SD0F1110 NG B/U

Бренд: Velux Страницы: 56

ECOMOD AHP60 14 kW

Бренд: Ideal Heating Страницы: 70

Бренд: Samoa Страницы: 40

Бренд: Binks Страницы: 40

Larius GHIBLI 10:1

Бренд: Samoa Страницы: 28

S-THERM+ SHP-140ERC

Бренд: Sinclair Страницы: 18

DUSTTRAK 8530EP

Бренд: TSI Instruments Страницы: 2

Бренд: U-Line Страницы: 9

Бренд: Alpha Solar Страницы: 16

VariAir VASF 2.50/X-1.AC115

Бренд: Becker Страницы: 8

RSJ-100/N1-540V-D

Бренд: Midea Страницы: 47

Бренд: Pentair Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды