Burster RESISTOMAT 2408 Скачать руководство пользователя страница 72

Страница: 72 / 90

RESISTOMAT

Model 2408

Page 72

2.8 Error Messages

“BAD DRIVE-REQUEST STRUCTURE”

Flash drive is either not connected or

defective

“BAD VOLTAGE SENT TO FUNCTION”

Improper voltage entered during

calibration procedure

“BAD ZERO CALIBRATION”

Zeroing error, repeat and/or remove

component from input terminals/fixture

(Refer to Note on p.63)

“CALIBRATION STANDARD OUT OF

Entered value > than 1% of 1 Megohm

RANGE”

“CORRUPT SETUP DATA”

Stored setups lost or corrupt (battery for

non-volatile memory may be defective or

has been disconnected)

“CRC ERROR ON USB”

Stored setup lost or corrupt (cyclic-

redundancy-check)

“PROTECT ERROR”

Flash drive is write protected

“ELAPSED TIME ERROR, SET TO 0”

Elapsed time is incorrect and has been

set to zero (battery for non-volatile memory

may be defective or has been disconnected)

“FAILURE # SEE DOCUMENTATION”

Hardware or software failure, 1 - 99

(# list not included in this manual)

“FILE ACCESS VIOLATION”

File selected from flash drive is Read Only

“FILE EXISTS”

File already exists under the chosen name

“USB DRIVE NOT READY”

Flash drive is either not connected or

defective

“USB MEDIA DEFECT”

Flash drive defective, format or replace

“USB READ FAULT”

Flash drive is either not connected or

defective

“USB SECTOR UNFORMATTED”

Flash drive is not formatted

Содержание RESISTOMAT 2408



























































































Результаты поиска

Содержание RESISTOMAT 2408

Отзывы:

Бренды по названию

Популярные бренды

Burster RESISTOMAT 2408, Руководство пользователя

Результаты поиска

Содержание RESISTOMAT 2408

Отзывы:

Бренды по названию

Популярные бренды