Burster 8627 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 21

Burster 8627 Скачать руководство пользователя страница 18

Page 18

Torque Sensor

Model 8627, 8628, 8632

8. Decommission

►

All sensors must be dismantled professionally.

►

Do not strike sensor housing with tools.

►

Do not apply bending moments on the sensor, e.g. through levers.

►

The torque sensor must be supported to avoid falling down during the

dismantling.

9. Transportation and Storage

The transportation of the sensor must occur in suitable packing. For smaller

sensors, stable cartons which are well padded are sufficient (e.g. air cushion
film, epoxy crisps, paper shaving). The sensor should be tidily packed into
film. Larger sensor should be packed in cases.

9.1

Transportation

Only release well packed sensors for transportation. The sensor should not be
able to move back and forth in the packing. The sensors must be protected
from moisture.

Only use suitable means of transportation.

9.2

Storage

The storage of the sensors must occur in dry, dust-free rooms, only. Slightly

lubricate shafts an flanges with oil before storing (rust).

«
...
16
17
18
19
20
...
»

Содержание 8627






















Отзывы:

Нет отзывов