Burl Audio B2 Bomber ADC Скачать руководство пользователя страница 9

Страница: 9 / 17

1. Download and install “

Dante Controlle

r” and purchase “

Dante Virtual Soundcard

,” or

Dante PCIe Card.

Dante Virtual Soundcard: -Go to www.audinate.com/products/software

Dante PCIe Card: -Focusrite Rednet PCIe card recommended

2. Using Cat6 Ethernet cable, connect the B2 Bomber to a gigabit switch. Connect your

DAW computer to the same switch with CAT6 cable. For best results, start by removing

all other connections to the switch. Dante should be on it’s own network.

3. Start by setting the B2 to Internal Clock, and desired sample rate (we recommend 96k).

4. Open “Dante Virtual Soundcard” (Figure 7)

- Click START to turn on Dante Virtual Soundcard.

5. Open “Dante Controller”

6. Click on ROUTING tab (Figure 8, page 9)

Click on the corresponding coordinates to enable device, as per Figure 8.

Note: Transmitters refers to signal coming from ADC to Dante card.

Receivers refers to Dante card sending signal to DAC.

DANTE QUICK START:

Figure 7

Содержание B2 Bomber ADC

















Результаты поиска

Содержание B2 Bomber ADC

Отзывы:

Похожие инструкции для B2 Bomber ADC

Бренды по названию

Популярные бренды

Burl Audio B2 Bomber ADC, Руководство пользователя

Результаты поиска

Содержание B2 Bomber ADC

Отзывы:

Похожие инструкции для B2 Bomber ADC

Бренды по названию

Популярные бренды