Burkert Type MS01 Скачать руководство пользователя страница 40

Страница: 40 / 88

pH sensor - Diagnostics

12.1.3

2-point calibration procedure of the pH sensor

Caution

Risk of injury due to the nature of the operating agents

▶

Respect the prevailing regulations on accident prevention and safety relating to the use of dangerous

fluids.

▶

Observe the information on the safety data sheet. The safety data sheets can be found at:

Cleaning solution acid:

http://sds-id.com/200111-2

Cleaning solution alkaline:

http://sds-id.com/200112-1

Flushing solution (reagent):

http://sds-id.com/200116-7

Buffer solution pH 5:

http://sds-id.com/200113-0

Buffer solution pH 7:

http://sds-id.com/200114-19

Buffer solution pH 9:

http://sds-id.com/200115-8

▶

Wear personal protective equipment when working with cleaning solutions.

▶

Dispose of waste containing chemicals produced by the system in an environmentally friendly manner.

Prerequisites:

•

Buy a Type MZ15 handheld calibration-and-cleaning tool with article number 00568805.

•

Buy a büS extension-cable. Refer to Table 7

. If needed, buy a Y junction.

Table 7: Accessories: cables and connectors

Accessories

Article number

büS extension-cable with 5-pin M12 connectors, 0.5 m

772403

büS extension-cable with 5-pin M12 connectors, 1 m

772404

büS extension-cable with 5-pin M12 connectors, 3 m

772405

büS extension-cable with 5-pin M12 connectors, 5 m

772406

Y junction

772420

•

Buy a buffer solution with pH 5, article number 806698 and a buffer solution with pH 9, article number

806700.

→

Read the Type MZ15 Operating Instructions.

→

Observe the information on the safety data sheets for the used solutions. The relevant data sheet can be

found at the address given on the bottom of the bottle.

→

For a correct use of the Type MZ15 handheld calibration-and-cleaning tool, refer to the Operating

Instructions of the Type MZ15.

→

Unlock and remove the product from the on the backplane of the system.

→

Plug the product on the Type MZ15 handheld calibration-and-cleaning tool. Refer to the Operating

Instructions of the Type MZ15

English

Type MS01

Содержание Type MS01

























































































Результаты поиска

Содержание Type MS01

Отзывы:

Похожие инструкции для Type MS01

Бренды по названию

Популярные бренды

Burkert Type MS01, Руководство по эксплуатации

Результаты поиска

Содержание Type MS01

Отзывы:

Похожие инструкции для Type MS01

Бренды по названию

Популярные бренды