Burkert 8022 Series Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 28

Burkert 8022 Series Скачать руководство пользователя страница 5

3

OperatingInstructions

1

Operating instructiOns

The Operating Instructions describe the entire life cycle of the device. Keep these instructions in a location which is
easily accessible to every user, and make these instructions available to every new owner of the device.

the Operating instructions manual contains important safety information.

Read the complete Operating Instructions. Pay special attention to the chapters Basic Safety Instructions and
Intended Use.

▶

Read the complete Operating Instructions.

1.1

symbols used

Caution!

Warns of a possible danger!

▶

Failure to observe this warning may result in a moderate or minor injury.

notE

Warns of damage to property!

▶

Failure to observe the warning may result in damage to the device or the equipment.

Indicates important additional information, tips and recommendations.

refers to information in these Operating Instructions or in other documentation.

▶

Indicates an instruction to be carried out to avoid a danger, a warning or a possible risk.

→

Indicates a procedure to be carried out.

Indicates the result of a specific instruction.

1.2

Definition of the term "device"

In these Operating Instructions, the term "device" always refers to the flow transmitter type 8022 or the pulse
divider type 8022.

English

Type 8022

«
...
3
4
5
6
7
...
»

Содержание 8022 Series





























Отзывы:

Нет отзывов