The TS-1 Dial Line Transient Suppressor provides transient voltage surge suppression for
equipment connected to a dial telephone line with standard RJ-13 or RJ-11 connectors.
The high quality die cast aluminum enclosure houses a passive, three-stage protection
device designed to conduct destructive energy safely to ground.
Both pairs in the RJ-13 standard configuration are afforded protection, while allowing the
normal ring voltage, and voice or data to pass unimpeded. Studio or transmitter audio
equipment connected to a two-pair dedicated stereo telco circuit may also be protected
with the TS-1.
The TS-1 must be connected to an adequate station ground to provide a path for
destructive energy to be shunted away from the protected equipment. Ideally, the TS-1
should be mounted on the copper strap directly connected to station ground. The integral
clamping system on the TS-1 affords easy mounting on strap up to four inches wide and
ensures a low-impedance path to ground. Alternatively, the TS-1 may be connected to earth
ground using the ground lug on the side of the enclosure.
INSTALLATION
Position the TS-1 near the telco service entry. In the event of a catastrophic lightning strike
to the phone line, this location prevents destructive energy from entering the facility.
Installation of the TS-1 is straightforward:
1. The preferred mounting scheme is to secure the
TS-1 to the station ground bus. First, remove the
machine screws from the TS-1. Beneath the
aluminum enclosure, you will find a thin
stainless steel shim on top of the stainless
steel backing plate. Clamp the ground bus
between the backing plate and shim, as
illustrated. Then attach the aluminum
enclosure so that it is flush with the stainless
steel shim and not touching the ground bus.
Secure the TS-1 by tightening the machine
screws (Phillips #8 x ½”).
TS-1
Dial Line
Transient
Suppressor
WARRANTY
Burk Technology, Inc.
warrants the TS-1 Transient Voltage Surge Suppressor to be free of
defects in materials and workmanship for a period of 24 months from the date of purchase.
Equipment will be repaired or replaced at the option of Burk Technology and returned
freight prepaid to the customer.
Damage due to abuse or improper operation or installation
of the equipment or caused by fire or flood or harsh environment is not to be covered by
this warranty.
Damage in shipping is not the responsibility of Burk Technology.
A return
authorization must be obtained before returning any equipment.
Materials returned under
this warranty must be shipped freight prepaid and insured in the original shipping carton or
suitable substitute to Burk Technology, 7 Beaver Brook Road, Littleton, MA 01460.
Repairs
not covered under this warranty will be made at prevailing shop rates established by Burk
Technology, Inc.
THE WARRANTY SET FORTH ABOVE IS IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
BURK
TECHNOLOGY, INC.
SHALL NOT BE LIABLE TO ANY PARTY FOR ANY INCIDENTAL,
SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF
THIS EQUIPMENT.
GETTING HELP
The Burk TS-1 is designed to protect indefinitely against multiple surges.
If a catastrophic
strike disables the TS-1, the device breaks the line circuit so there is no loss of protection.
Therefore, if an otherwise functional telephone line is inoperative when connected to the
TS-1, the unit may need factory repair.
For assistance with the TS-1, please contact Burk Technology customer support:
Phone:
978-486-3711
Web:
www.burk.com
Email:
Contact the sales department toll free at 800-255-8090, or email [email protected].
TS-1 USER GUIDE,
REV
D
Copyright ©
20
15
Burk Technology, Inc.
All rights reserved.
No part of this manual may be reproduced in any form
or by any means without written permission from Burk Technology.
Information in this manual is subject to change
without notice.
User Guide
