ProfiScale LASER METER 50 PS 7550
4
English
|
4
Measurement functions
Length measurement
Length measurement is preset when the device is switched on. The display
indicates the length measurement symbol. Aim at the end of the measured
distance and press the button “A” again. The reading is indicated below in
the “12” display.
Surface area measurement
Press the button “C” once in order to select surface area measurement. The
display indicates the symbol for surface area measurement, the first surface
length flashes. Aim at the desired target and press the button “A” once to
take the measurement. The reading is indicated above in the “10” display,
while the second surface length flashes. Use the laser to aim at the next target
and press the button “A” to take the measure ment. The reading is indicated
in the “11” display, while the resulting surface area has been calculated and
indicated in “12”.
Volume measurement
Press the button “C” twice in order to select volume measurement. The
display indicates the symbol for volume measurement, the first volume length
flashes. Aim at the desired target and press the button “A” to take the first
measurement. The reading is indicated above in the “10”display, while the
second volume length flashes. Use the laser to aim at the next target and press
the button “A” to take the measurement. Proceed in a similar way for the third
length. The reading is indicated in the “11” display, while the resulting volume
has been calculated and indicated in “12”. Indirect length measurement Using
this function you can measure directly inaccessible distances (e. g. exterior wall
heights), as two or three measurable lengths are mutually related based on
trigonometric functions.
Measurement based on two lengths
Press the button “D” once in order to select indirect length measurement.
The display indicates the indirect measurement symbol, the first length flashes.
Aim at the desired target and press the button “A” once to take the first
measurement. The reading is indicated above in the “10” display, while the
second length in the display flashes. Use the laser to aim at the next target and
press the button “A” to take the measurement. The reading is indicated in the
display, while the re sulting length has been calculated and indicated in “12”.
Measurement based on three lengths
Press the button “D” twice in order to select indirect length measurement based
on three lengths. The display indicates the indirect measurement symbol, the
first length flashes. Aim at the desired target and press the button “A” once to
take the first measurement. The reading is indicated above in the “10” display,
while the second length in the display flashes. Use the laser to aim at the next
target and press the button “A” to take the measurement. The reading is
indicated in the display. Proceed in a similar way for the third length. The reading
is indicated in the display, while the re sulting length has been calculated and
indicated in “12”.
Continuous measurement
The continuous measurement function is intended for deriving dimensions
for instance from construction plans. The minimum and maximum
values can also be determined in this way. When this function is used,
the measurement device moves relative to the target, while the reading is
updated approx. every 0.5 sec. During this, the minimum distance is indicated
in the “10” display and the maximum distance in the “11” display. The
currently measured value is always indicated in the “12” display. Press the
button “5“ for approx. 3 sec until you receive an indication and move the
measure ment device. The distances are indicated in the display. To deactivate
the function, press the button “A”. The function switches off automatically
after 100 measurements.
Computing operations
Addition
This is intended to add two or more lengths. When you have measured
the first length, press the add symbol “K”. The reading is indicated above
in the “10” display, while the “+” symbol in the display flashes. Press the
button “A” again, and the total is indicated in the bottom line. You can
add more values in this way.
Subtraction
When you have measured the first length, press the subtract symbol “J”.
The reading is indicated above in the “10” display, while the “–“ symbol in
the display flashes. Press the button “A” again, and the total is indicated in
the bottom line. In this way, you can subtract more values from each other.
Memory function
The memory function contains the 10 last readings. For this purpose, press
the button “G”. The memory values can be scrolled using the Add and
Subtract buttons (buttons “J” and “K”) and thus shown in the display.
Individual readings can be deleted from the list using the Delete button “H”.
Lighting and unit selection button
The display lighting can be switched on and off by pressing the lighting or
unit selection button briefly. When the button is pressed for a longer time,
the unit of measure of the readings changes (m, ft, in, ft+in).
Causes and removal of errors
The device will help you in case of measurement troubles, as various codes
are indicated in the display.
Error Codes
Correction
204
Calculation error
Repeat the process
208
Received signal is too weak,
measurement takes too long
Measured distance > 50m.
Measurement with
a target plate
209
Received signal is too strong.
Measurement with a target plate
252
Temperature is too high
Cool the device down
253
Temperature is too low
Warm up the device
255
Device failure
Switch the device on and off
several times. In case the error
message persists, please contact
your dealer.
Disposal of the device
Dear customer,
please help us to reduce waste. Should you ever intend to dispose of
this device, please bear in mind that many components of the device
contain precious materials, which can be recycled. Please do not dispose
of this device as common waste, but rather request information from the
responsible local authority on the collecting points for electric waste.
The dustbin symbol indicates:
Discharged batteries or accumulators must not be disposed as
common waste. Please return the batteries/accumulators to
their vendor or the local recycling yard. Their return is free of
charge and it is legally required.
Errors and changes reserved.
