background image

Page 23

FIG. 17 START SWITCH TERMINALS

P1283

SERVICE (cont.)

START SWITCH

FIG. 16 START SWITCH

P2150.40

Location:

The start switch is located in the front of the hood,

above and to the far right of the brew funnel.

Test Procedure:
1. Disconnect the brewer from the power source.
2. Remove the wires from the terminals.
3. Check for continuity across the two terminals on

the side of the switch from which the wires were
removed, when the switch is held in the lower po-
sition. Continuity must not be present across these
terminals in the upper position.

If  continuity  is  present  as  described,  the  switch  is
operating properly.
If continuity is not present as described, replace the
switch.

Removal and Replacement:
1. Remove the wires from the switch terminals.
2. Compress  the  clips  inside  the  hood  and  gently

push the switch through the opening.

3. Push the new switch into the opening and spread

the clips to hold the switch captive in the hood.

4. Refer to Fig. 17 when reconnecting the wires.

WHI/YEL to Sanitize
Switch
WHI/YEL to Control
Board J5-1

WHI/ORN to Control
Board J5-6

33030 052600

Содержание TU3QF-EZ



























Отзывы: