Bunn Single SH BrewWISE DBC страница 41 Скачать руководство пользователя

Страница: 41 / 54

Page 41

TROUBLESHOOTING

A troubleshooting guide is provided to suggest probable causes and remedies for the most likely problems

encountered. If the problem remains after exhausting the troubleshooting steps, contact the Bunn-O-Matic

Technical Service Department.

•

Inspection, testing, and repair of electrical equipment should be performed only by qualified

service personnel.

•

All electronic components have 120 - 240 volt ac and low voltage dc potential on their terminals.

Shorting of terminals or the application of external voltages may result in board failure.

•

Intermittent operation of electronic circuit boards is unlikely. Board failure will normally be per-

manent. If an intermittent condition is encountered, the cause will likely be a switch contact or

a loose connection at a terminal or crimp.

•

Solenoid removal requires interrupting the water supply to the valve. Damage may result if sole-

noids are energized for more than ten minutes without a supply of water.

•

The use of two wrenches is recommended whenever plumbing fittings are tightened or loosened.

This will help avoid twists and kinks in the tubing.

•

Make certain that all plumbing connections are sealed and electrical connections tight and iso-

lated.

•

This brewer is heated at all times. Keep away from combustibles.

WARNING

•

Exercise extreme caution when servicing electrical equipment.

•

Disconnect the brewer from the power source when servicing, except when electrical tests are

specified.

•

Follow recommended service procedures.

•

Replace all protective shields or safety notices.

Screen Displayed

Possible Cause

Troubleshooting Procedures

1. Overflow cup is full of water. This

could be caused by boiling; see chart

on page 31. Also could be Refill Sen-

sitivity adjustment; see page 32.

1. Soft Heat Server not correctly

positioned on base.

2. Not using a Soft Heat Server, and

the

SERVER DETECT

function is

activated (on).

Empty cup. Correct cause and

retry.

Position the server so that the con-

nector pins on the server make con-

tact with connector on the brewer.

Disable the

SERVER DETECT

func-

tion.

OVERFLOW CUP

FULL. EMPTY CUP

SERVER NOT

IN PLACE

29877-3 062005

Содержание Single SH BrewWISE DBC























































Результаты поиска

Содержание Single SH BrewWISE DBC

Отзывы:

Похожие инструкции для Single SH BrewWISE DBC

Бренды по названию

Популярные бренды

Bunn Single SH BrewWISE DBC, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Single SH BrewWISE DBC

Отзывы:

Похожие инструкции для Single SH BrewWISE DBC

Бренды по названию

Популярные бренды