background image

2

44806.1 050511

BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY

Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:

1) All equipment other than as specified below: 2 years parts and 1 year labor.

2) Electronic circuit and/or control boards: parts and labor for 3 years.

3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.

4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis: 

parts and labor for 3 years or 30,000 pounds of coffee, whichever comes first.

These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by 

it will be commercially free of defects in material and workmanship existing at the time of manufacture and 

appearing within the applicable warranty period. This warranty does not apply to any equipment, component or 

part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect, 

alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is 

conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone 

at (217) 529-6601 or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by 

BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior 

authorization from BUNN that the defective equipment is under warranty.

THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR 

ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER 

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN 

are not authorized to make modifications to this warranty or to make additional warranties that are binding on 

BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and 

should not be relied upon.

If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its 

exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts 

and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective 

components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace 

the equipment or refund the purchase price for the equipment.

THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF 

THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S 

SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.

In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, 

loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute 

equipment, facilities or services, or any other special, incidental or consequential damages.

392, AutoPOD, AXIOM, BrewLOGIC, BrewMETER, Brew Better Not Bitter, BrewWISE, BrewWIZARD, BUNN Espress, BUNN 

Family Gourmet, BUNN Gourmet, BUNN Pour-O-Matic, BUNN, BUNN with the stylized red line, BUNNlink, Bunn-OMatic, 

Bunn-O-Matic, BUNNserve, BUNNSERVE with the stylized wrench design, Cool Froth, DBC, Dr. Brew stylized Dr. design, 

Dual, Easy Pour, EasyClear, EasyGard,  FlavorGard, Gourmet Ice, Gourmet Juice, High Intensity, iMIX, Infusion Series, 

Intellisteam, My Café, PowerLogic, Quality Beverage Equipment Worldwide, Respect Earth, Respect Earth with the styl-

ized leaf and coffee cherry design, Safety-Fresh, savemycoffee.com, Scale-Pro, Silver Series, Single, Smart Funnel, Smart 

Hopper, SmartWAVE, Soft Heat, SplashGard, The Mark of Quality in Beverage Equipment Worldwide, ThermoFresh, Titan, 

A Partner You Can Count On, Air Brew, Air Infusion, Beverage Bar Creator, Beverage Profit Calculator, Brew better, not 

bitter., BUNNSource, Coffee At Its Best, Cyclonic Heating System, Digital Brewer Control, Nothing Brews Like a BUNN, 

Pouring Profits, Signature Series, Tea At Its Best, Phase Brew, The Horizontal Red Line, trifecta, Ultra, Velocity Brew are 

either trademarks or registered trademarks of Bunn-O-Matic Corporation.

Содержание LCA-1
























Отзывы: