background image

Page 7

For technical questions, please call 1-888-866-5797.

Item 64910 
        

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM 
IN THIS DOCUMENT AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER OR DISTRIBUTOR 
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS 
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE 
ANY PARTS OF THE PRODUCT.  IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY 
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND 
LICENSED TECHNICIANS, AND NOT BY THE BUYER.  THE BUYER ASSUMES ALL RISK AND LIABILITY 
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS 
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Parts List and Diagram

Part

Description

Qty

A

Light Fixture

1

B

Screw Cover

1

C

Bracket

1

D

Fixture Screw

1

E

Base

1

Part

Description

Qty

F

Bracket Screw #8/32x1/2 in

2

G

Motion Sensor

1

H

Bracket Screw #6/32x1/2 in

2

I

Bracket Screw #10/32x1/4 in

2

J

Base Screw

1

Record Serial Number Here: 

Note:

 If product has no serial number, 

record month and year of purchase instead.

Note:

 Some parts are listed and shown for 

illustration purposes only, and are not available 
individually as replacement parts.

Содержание 64910









Отзывы: