AUXILIARY INPUT
If you wish to use this starter with an aftermarket alarm, connect the BLUE wire from the 18-pin
harness to the second or third channel (-) output of your existing alarm. When the output is
activated, a (-) signal will be supplied to the remote starter.
TRUNK RELEASE OUTPUT (Optional Part #775
required)
Locate the trunk release wire coming from
the back of the trunk release switch. To
determine if your trunk release is tripped
by a (+) positive or a (-) negative (most
trunk release switches are (+) positive).
Place one end of your test light to ground,
probe the wire. Press the “Trunk” button,
if the test light illuminates, you have a
(+) positive trunk release. If it does not,
connect the test light to +12V constant
and probe the wire. If the test light
illuminates when the button is pressed,
then you have a (-) negative trunk release.
Connect the WHITE WITH RED STRIPE wire to
the WHITE wire of the optional relay.
Please use figures below for correct
connections.
4. Dome Light Option
The remote starter includes an optional output that can be used to illuminate the dome light when pressing
button #2 and unlocking your power door locks. The dome light will remain on for one minute or until you
turn the ignition on or press the brake.
5. Trunk Release Output
The remote car starter includes an optional output that can be used to do one of the following: open the
trunk (optional part #775 required), roll up the windows (optional module part #WRU-B), close the sun roof
(optional part #775 required) etc. This output will pulse .75 seconds when pressed and released. In instances
where a continuous signal is needed such as sun roof and power windows, hold down button #3 (trunk) as long
as the signal is needed to complete the task. The parking lights will remain on as long as this button is
being pressed.
6. Runtime Confirmation (Engine Not Running)
To check programmed runtime, press and release button #4 (stop), the parking lights will flash for the programmed
length of time. Each flash will equal 5 minutes of runtime.
2. Pit Stop: Exiting the Car with the Engine Running
Make sure the transmission is in park and press button #1 (start) before turning the ignition switch off.
(The engine will remain running for the preset time.)
3. Keyless Entry Operation
Press button #2 (lock/unlock), the parking lights will flash once and the doors will lock. Press button #2
again, the parking lights will flash twice, the doors will unlock, and the parking lights will remain on for
one minute or until you turn the ignition on or press the brake.
OPERATING INSTRUCTIONS
1. Starting the Vehicle with the Remote Transmitter
Press and release button #1 (start). The parking
lights will flash once, confirming the car starter
received the signal. The car will then start and
the parking lights will turn on and remain on while
the vehicle is running. To shut off the engine
before the preset time, press button #4 (stop) or
press the brake pedal. NOTE: If your car does not
start on the first crank it will automatically
attempt to start up to 2 more times. (only in
tachless mode) In tachless mode, parking lights
will wait approximately 10 seconds before turning
on.
BUTTON #1
Starts your vehicle from 400 feet
away. (E-Model, up to 800 feet)
BUTTON #2
Locks and unlocks your power door
locks.
BUTTON #3
Pops your trunk
BUTTON #4
Shuts engine off and programs runtime.
BULLDOG
Start
Lock
Unlock
Trunk
Stop
PROGRAMMING INSTRUCTIONS
ENTERING PROGRAMMING MODE
Make sure your vehicle is not running and the brake is pressed. The brake is to remain pressed as long as you want
to remain in programming mode. The only exception is when a different remote has been learned. The unit will exit
the programming mode simply by releasing the brake and the parking lights will flash three (3) times.
Adding Additional Remotes
Press and hold brake. Next, press and hold Button #1 on the working remote until the parking lights flash once. Release.
Press and release Button #4 on the new remote. The parking lights will flash three (3) times confirming that the new
remote was learned.
Automatic Start - Off
Press and hold brake. Press and hold Button #2 until the parking lights flash twice. Release. Press and release Button
#1. The parking lights will flash twice. The automatic start is programmed OFF. Release the brake, the parking lights
will flash three (3) times. NOTE: Factory setting is OFF.
9
