Bulldog Security 5002PRO Скачать руководство пользователя страница 5

Страница: 5 / 14

4. Insert the wire from the unit through the hole as shown.

6. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the

connection. First pull the wire that you have just connected along side the wire you connected
to, tape and wire tie them together. Use this method for all connections.

CAUTION: All wires must be wrapped and taped.

5. Wrap the wire around one side then the other and finally around itself as shown.

Wire Tie

Electrical Tape

3. Lay upper twisted pair of wires over right wire as shown. Bring lower twisted pair of wires

up to meet the left wire as shown.

2. Twist upper wires together, twist lower wires together as shown.

1. When tying two separate wires together at their ends, strip back 1” of insulation on both

wires and separate the strands of wire as shown below.

MAKING END TO END CONNECTIONS

FOLLOW THESE INSTRUCTIONS

Содержание 5002PRO















Результаты поиска

Содержание 5002PRO

Отзывы:

Похожие инструкции для 5002PRO

Бренды по названию

Популярные бренды

Bulldog Security 5002PRO, Руководство по установке

Результаты поиска

Содержание 5002PRO

Отзывы:

Похожие инструкции для 5002PRO

Бренды по названию

Популярные бренды