background image

SAFETY INSTRUCTIONS 

  

 
 
This power burner must be installed in accordance with local codes or, if in an area without local codes, with the latest edition of the National Fuel 

Gas Code ANSI Z223.1. In Canada, installation must conform to the standard CAN/ CGA 1-b149.1 and/or .2 (Installation Code for Gas Burning 

Appliances and Equipment) and any local codes. 

 
WARNING

: Fuels used in gas or oil-fired appliances and the products of combustion of such fuels, contain chemicals known to the State of 

California to cause cancer, birth defects and/or reproductive harm. This warning is issued pursuant to California Health & Safety Code Sec. 

25249.6. 
 

THE LOCATION FOR YOUR POWER BURNER 

 

DO NOT use your power burner in garages, porches, breezeways, sheds or other enclosed areas.

 Your power burner is to be used 

OUTDOORS ONLY

, with at least 

21 inches

 clearance from the back and side of any combustible surface. The power burner should not be placed 

under or on top of any surface that will burn. Do not obstruct the flow of combustion and ventilation air around the power burner housing. 

 
PROTECT CHILDREN: 

Keep children away from the

 

power burner during use and until the power burner has cooled after you are finished. Do not 

allow children to operate the power burner. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

CHECKING FOR GAS LEAKS 

 

NEVER TEST FOR GAS LEAKS WHILE THE POWER BURNER IS LIT!

 Prior to the first use and at the beginning of each new season (or, if using 

LP, whenever gas cylinder is changed), it is a must that you check for gas leaks. Follow these steps: 
1. Make a soap solution by mixing one part liquid detergent and one part water. 
2. Turn off heat control valve(s), and then turn on gas at source. 
3. Apply the soap solution to all gas connections: bubbles will appear in the soap solution if connections are not properly sealed. Tighten or repair 

as necessary. 
4. If you have a gas leak that you cannot repair, turn off the gas at the source, disconnect fuel line from the power burner and immediately call your 

burner dealer and gas supplier for professional assistance. 

 

FOR YOUR SAFETY... 

 

DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 
 
DO NOT store empty or full spare gas cylinders and/or chemicals under or near this or any other appliance. 
 
Keep the fuel hose away from hot surfaces. Protect the fuel hose from dripping grease and/or liquids. Avoid unnecessary 

twisting of the hose. Visually inspect the hose prior to each use for cuts,

 

cracks excessive wear or other damage and replace if 

necessary. 
 
NEVER test for gas leaks with a lighted match or open flame. 
 
NEVER light power burner with lid on or before checking to ensure burner tubes are fully seated over gas orifices. 
 
NEVER lean over cooking surface while lighting power burner. Use good quality insulated potholder mitts. Use dry mitts only; 

damp or wet mitts on a hot surface may cause steam which could result in personal injury.

 

IF YOU SMELL GAS... 
1. Shutoff gas to the appliance at its’ source. 
2. Extinguish any open flame. 
3. Remove power burner lid to release any accumulation of fumes. 
4. If gas odor persists

immediately contact your gas supplier.

 

READ CAREFULLY BEFORE ASSEMBLY AND OPERATION OF YOUR POWER BURNER 

Содержание 96000



















Отзывы: