background image

27

To Open the Door Manually

The door should be fully closed if 
possible. Pull down on the emergency 
release handle and lift the door 
manually. To reconnect the door to the 
opener, press the door control push 
bar.

The 

lockout feature

 prevents the 

trolley from reconnecting 
automatically. Pull the emergency 
release handle down and back (toward 
the opener). The door can then be 
raised and lowered manually as often 
as necessary. To disengage the 
lockout feature, pull the handle 
straight down. The trolley will 
reconnect on the next UP or DOWN 
operation, either manually or by using 
the door control or remote.

To prevent possible SERIOUS INJURY OR DEATH from a falling 
garage door:
•  If possible, use emergency release handle to disengage 

trolley ONLY when garage door is CLOSED. Weak or broken 
springs or unbalanced door could result in an open door 
falling rapidly and/or unexpectedly.

•  NEVER use emergency release handle unless garage doorway 

is clear of persons and obstructions.

•  NEVER use handle to pull door open or closed. If rope knot 

becomes untied, you could fall.

Trolley
Release 
Arm

NO

TICE

Emergency
Release 
Handle
(Pull Down)

Trolley
Release 
Arm

NOTICE

Emergency
Release Handle
(Down and Back)

LOCKOUT POSITION

MANUAL DISCONNECT POSITION

Using the Wall-Mounted Door Control

Press the button to open or close the door. 
Press again to reverse the door during the 
closing cycle or to stop the door while it's 
opening.

Содержание 1345BMM





































Отзывы: