background image

Hub

 

Product Manual

   

|   5

4   |   Hub

 

Product Manual

Notices

FCC RSS-GEN SEC 7.1.3 NOTICE:

This device complies with Industry Canada  

license-exempt RSS standard(s). Operation is 

subject to the following two conditions: (1) this 
device may not cause interference, and (2) this 
device must accept any interference, including 
interference that may cause undesired operation 
of the device.

Le présent appareil est conforme aux CNR 
d’Industrie Canada applicables aux appareils radio 
exempts de licence. L’exploitation est autorisée 
aux deux conditions suivantes: (1) l’appareil ne 
doit pas produire de brouillage, et (2) l’utilisateur 
de l’appareil doit accepter tout broillage 
radioélectrique subi, même si le brouillage est 
susceptible d’en compromettre le fonctionnement.

This equipment has been tested and found 

to comply with the limits for a Class B digital 
device, pursuant to part 15 of the FCC 
Rules. These limits are designed to provide 
reasonable protection against harmful 
interference in a residential installation.  

This equipment generates, uses and can 

radiate radio frequency energy and, if not 
installed and used in accordance with the 
instructions, may cause harmful interference  
to radio communications. However, there  
is no guarantee that interference will not occur 
in a particular installation. If this equipment 
does cause harmful interference to radio  
or television reception, which can be 
determined by turning the equipment off  
and on, the user is encouraged to try  
to correct the interference by one or more  
of the following measures:

• Reorient or relocate the receiving antenna. 

• Increase the separation between the equipment 

and receiver. 

• Connect the equipment into an outlet on 

a circuit different from that to which the receiver  
is connected. 

• Consult the dealer or an experienced radio/TV 

technician for help.

FCC 15.21 NOTICE:

The grantee is not responsible for any changes or 

modifications not expressly approved by the party 
responsible for compliance. Such modifications 
could void the user’s authority to operate the 
equipment. 

IC NOTICE:

Under Industry Canada regulations, this radio 
transmitter may only operate using an antenna 
of a type and maximum (or lesser) gain approved 
for the transmitter by Industry Canada. To reduce 
potential radio interference to other users, the 
antenna type and its gain should be so chosen that 
the equivalent isotropically radiated power (e.i.r.p.) 
is not more than that necessary for successful 
communication.

Conformément à la réglementation d’Industrie 
Canada, le présent émetteur radio peut fonctionner 
avec une antenne d’un type et d’un gain maximal 
(ou inférieur) approuvé pour l’émetteur par 
Industrie Canada. Dans le but de réduire les risques 
de brouillage radioélectrique à l’intention des 
autres utilisateurs, il faut choisir le type d’antenne 
et son gain de sorte que la puissance isotrope 
rayonnée équivalente (p.i.r.e.) ne dépasse pas 

l’intensité nécessaire à l’établissement d’une 
communication satisfaisante.

Содержание H200BRA









Отзывы: