background image

 

6  

Safety

• 

Never work beneath raised loader unless it 
is securely supported.  The following are 
instructions for the Lift Lock Supports; 

-DO NOT USE WHEN TRACTOR IS MOVING.
-DO NOT STORE LIFT LOCK SUPPORTS OTHER THAN WHERE INDICATED.
-REPLACE IMMEDIATELY IF DAMAGED.

-THE BUCKET MUST BE EMPTY
-ALWAYS USE BOTH SUPPORTS

TO DISENGAGE SUPPORTS:

1. RAISE LOADER OFF LIFT LOCK 
SUPPORTS.
2. SWING LOCK SUPPORTS UP INTO 
STORAGE POSITION.

LIFT LOCK INSTRUCTIONS

TO ENGAGE SUPPORTS:

1.  RAISE LOADER PAST LEVEL           
POSITION
2. SECURE SUPPORTS INTO 
POSITION ON THE CLEVIS AND 
CYLINDER SHAFT.
3. SLOWLY LOWER FULL WEIGHT OF      
LOADER ONTO SUPPORTS.

IMPORTANT:

Lift Cylinder Shaft

Lift Lock

Support

Clevis

 

 

• 

Do not pivot or turn tractor with bucket raised, 
except at a minimum speed.  Always make 
allowance for length of loader when making 
turns. 

 

• 

Never leave tractor unattended while the 
bucket is raided.  Always lower bucket to the 
ground and shut off before leaving tractor seat. 

 

• 

Do not walk under raised bucket. 

 

• 

Never operate loader while operator is not 
seated in the driver’s seat on the tractor. 

 

• 

Keep tractor on solid ground.  Loose fill, rocks 
and holes can be dangerous for loader 
operation or movement. 

 

• 

Never operate a loader with frayed or damaged 
hoses or leaking fittings. 

 

• 

Add ballast as required to ensure 25% of 
gross vehicle weight is transferred to the 
rear axle. 

 
 
 
 
 
 
 
 
 
 

• 

Space rear tires as recommended by 
tractor manufacturer.  Maximize width 
for high lift applications. 

 

 

• 

Do not raise bucket to extreme heights 
while tractor is on an incline.  Carry 
loader low for safety.  Note in above 
illustration how load center moves out 
when bucket is raised on a slope.  Be 
alert for terrain changes and adjust 
bucket accordingly.  Keep bucket low, 
no more than one foot high, as long as 
possible. 

 

• 

Note:  A pivoting front axle acts like a 
three-wheeled tractor until the stops hit 
the axle. 

 

 

• 

If lift cylinders are used to raise front 
wheels of tractor for service, place 
blocks under tractor before working 
around front end. 

 

THIS SAFETY ALERT SYMBOL MEANS: 

ATTENTION! 

BECOME ALERT! 

YOUR SAFETY IS INVOLVED! 

 

 

Содержание Allied 595



































Отзывы: