Buffalo Tools HIT140 Скачать руководство пользователя страница 19

Страница: 19 / 22

3. The LAP SPOT METHOD directs the welding arc to penetrate the bottom and top pieces, at the same time, right

along each side of the lap joint seam. Select the wire diameter, heat setting, and tune in the wire speed as if you

were welding the same thickness material with a continuous bead.

6.6 SPOT WELDING INSTRUCTIONS

1. Select the wire diameter and heat setting recommended above for the method of spot welding you intend to use.

2. Tune in the wire speed as if you were going to make a continuous weld.

3. Hold the nozzle piece completely perpendicular to and about 1/4 inch off the work piece.

4. Pull the trigger on the torch and release it when it appears that the desired penetration has been made.

5. Make practice spot welds on scrap metal, varying the length of time you hold the trigger, until a desired spot

weld is made.

6. Make spot welds on the actual work piece at desired locations.

Maintenance

The welder needs the regular maintenance as following:

Periodically clean dust, dirt, grease, etc. from your welder. Every six months, or as necessary, remove the cover

panel from the welder and air-blow any dust and dirt that may have accumulated inside the welder.

TROUBLESHOOTING

Содержание HIT140























Результаты поиска

Содержание HIT140

Отзывы:

Похожие инструкции для HIT140

Бренды по названию

Популярные бренды

Buffalo Tools HIT140, Инструкции по сборке и эксплуатации

Результаты поиска

Содержание HIT140

Отзывы:

Похожие инструкции для HIT140

Бренды по названию

Популярные бренды