manualshive.com logo in svg

Buffalo Tools GEN4000DF-STW, Инструкция по эксплуатации

Поделиться
Скачать
Buffalo Tools GEN4000DF-STW Скачать руководство пользователя страница 18

GEN4000DF-STW 4000 Surge Watt / 3500 Running Watt Portable Dual Fuel  Gen  Welder  

 

 

18 

DC Usage 

 

                                                                                     

 

The DC outlet is only for recharging 12 Volt automotive-type batteries. Do not connect any other device to this outlet.

 

 

                                                                                     

  

Use this generator only for recharging 12 Volt batteries. NEVER attempt to jumpstart a car with this generator.

 

 

                                                                                     

 

Failing to use the correct procedure can cause a battery to explode, seriously injuring anyone nearby. Keep heat, sparks, flame and 

smoking materials away from the battery.

 

 
To connect 12 Volt batteries to the DC outlet: 
1. Connect the red charging wire to the positive terminal of the battery and the black charging wire to the negative terminal of the battery. 
2. Connect the plug end of the wire to the 12V DC outlet on this generator. 
3. Start this generator. 
4. When disconnecting, always disconnect the wires from this generator first to avoid a spark. 
 

                                                                                         

 

Storage batteries emit highly explosive hydrogen gas when charged.

 

Batteries also contain acid, which can cause severe chemical burns. 

• Do not allow open flames or cigarettes nearby for several minutes after charging a battery. 
• Always wear protective goggles and rubber gloves when charging a battery. 
 

• If battery acid gets on the skin, flush with water. 

 

• If battery acid gets in the eyes, flush with water and immediately call a physician. 

 

• If battery acid is swallowed, drink large quantities of milk and immediately call a physician. 

 

STOPPING THE GENERATOR 

 
To stop this generator: 
1. Turn off all connected electrical devices and then unplug them. 
2. Allow this generator to run for several more minutes with no electrical devices connected to help stabilize the temperature of this generator. 
3. Turn off the engine switch. 
4. If using Propane, turn the propane tank fuel valve to the “off” position. 
 

                               

                                                          

   

Allow this generator to cool down before touching areas that become hot during operation.

 

 

MAINTENANCE/CARE 

 
Proper routine maintenance of this generator is essential for safe, economical, and trouble-free operation. It will help prolong the life of this generator 
as well as help reduce air pollution. Perform maintenance checks and procedures according to the schedule in Figure 10. 
 

STOP!

 

If you have questions about maintenance procedures described in this manual, 

call 1-866-460-9436 , Monday - Friday, 8 AM - 4 PM Central Time.

 

 

                                                                                                  

 

Never perform maintenance procedures while this generator is running. Allow this generator to cool before commencing any maintenance 
procedures. Keep heat, sparks and flame away.

 

 

                               

                                                                  

 

Improper maintenance and/or failure to correct any problems prior to operating this generator can cause a malfunction which could cause 
death or serious injury. Always follow the inspection and maintenance recommendations and schedules in this manual.

 

 

Содержание GEN4000DF-STW















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды