Buell XB 2010 Скачать руководство пользователя страница 545 | Manualshive

Страница: 545 / 714

background image

6.26

MAIN WIRE HARNESS

GENERAL

The main wire harness runs from the front of the motorcycle
to the tail section.

Always replace plastic tree fasteners when replacing main wire
harness. Remove tree fasteners carefully, do not leave any of
fastener in frame.

REMOVAL

NOTES

•

To verify correct installation, make note of wire routing
and cable strap locations before removing main wire har-
ness.

•

Main wire harness is removed from rear of vehicle through
fan section of frame.

1.

Remove seat.

2.

Remove air cleaner assembly. See

4.3 AIR CLEANER

.

3.

Remove sprocket cover. See

2.36 SPROCKET COVER

Disconnect negative (-) battery cable first. If positive (+)
cable should contact ground with negative (-) cable con-
nected, the resulting sparks can cause a battery explosion,
which could result in death or serious injury. (00049a)

4.

Remove battery.

a.

Disconnect battery negative cable (black) from battery
negative (-) terminal.

b.

Pull back terminal cover boot on battery positive cable
(red).

c.

Disconnect battery positive cable from battery positive
(+) terminal.

NOTE

On Firebolt models it will be necessary to remove tail frame
upper body work. See

2.39 SUBFRAME TAIL ASSEMBLY

AND BODY WORK: FIREBOLT

.

5.

. Disconnect positive battery cable (1) and

starter solenoid connection [128] (3) from starter.

6.

Disconnect vehicle speed sensor [65] (2).

NOTES

•

On Firebolt models the rear brake switch connector is
located under the seat in front of the rear break reservoir
hose.

•

On Firebolt models the fuse block and relay block are
attached to the fairing support bracket.

7.

On Firebolt models, remove the main fuse case located
to the right of the battery towards the left side of the
vehicle.

NOTES

•

Reference the correct figure for the vehicle you are servi-
cing:

•

Lightning: See

.

•

Firebolt: See

•

Ulysses: See

.

8.

Disconnect:

a.

Main harness ground [GRD 2].

b.

Rear brake light switch connector [121].

c.

ECM connectors [10] and [11].

d.

BAS (bank angle sensor) connector [134].

e.

Right turn signal connector [18].

f.

Left turn signal connector [19].

g.

License plate lamp connector [45].

h.

Tail light connectors [93].

i.

Low voltage ground terminals on left side tail section
[GRD 1] and [GRD 3].

j.

Interactive exhaust connector [165B], (located under
main wiring harness).

9.

Remove fuse block and relay center from support bracket.

10. Remove the rear shock absorber assembly and reservoir.

See

2.23 REAR SHOCK ABSORBER

11. Remove fan. See

4.11 COOLING FAN

.

2

3

1

sm03752

1.

Positive battery cable

2.

Vehicle speed sensor

3.

Starter solenoid

Figure 6-91. Positive Battery Cable (Protective Boot Not

Shown)

2010 XB Service: Electrical 6-71

«
...
543
544
545
546
547
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: N-Com Страницы: 2

Бренд: N-Com Страницы: 64

Бренд: Sena Страницы: 25

Бренд: paladin Страницы: 2

Бренд: N-Com Страницы: 32

WOLVERINE X4 2021

Бренд: Yamaha Страницы: 192

Бренд: Yamaha Страницы: 224

Бренд: Yamaha Страницы: 343

Бренд: Yamaha Страницы: 404

Бренд: Yamaha Страницы: 432

Бренд: Yamaha Страницы: 404

Бренд: Yamaha Страницы: 694

Бренд: Yamaha Страницы: 864

Бренд: Yamaha Страницы: 912

Бренд: Yamaha Страницы: 864

Бренд: Yamaha Страницы: 110

Бренд: hepco & becker Страницы: 4

Бренд: Memphis Shades Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды