Buell XB 2010 Скачать руководство пользователя страница 437 | Manualshive

Страница: 437 / 714

background image

12. Remove scissor jack from motorcycle.

2

1

3

sm00303

1.

Drive belt not fully seated in rear sprocket

2.

Squeezing drive belt in order to seat in pulleys

3.

Drive belt fully seated in rear sprocket

Figure 5-41. Seating Drive Belt Into Pulley Teeth

IDLER PULLEY REMOVAL

NOTE

On the Ulysses models, it is necessary to remove the right side
rider footrest support in order to remove the idler pulley.

1.

. Loosen rear axle pinch bolt (2).

2.

Unthread axle approximately 15 rotations to release ten-
sion from drive belt.

3.

Remove chin fairing fasteners. See

2.50 CHIN FAIRING

4.

Remove front sprocket cover. See

.

5.

. Remove idler pulley bracket nuts and

washers (5) from studs (3).

6.

Slide idler pulley bracket (4) off studs (3).

7.

Inspect pulley by spinning wheel (1) and checking for
wheel bearing wear. See

1.11 DRIVE BELT MAINTEN-

ANCE, Inspection

.

8.

If pulley wheel needs replacement, remove fastener (6),
washer and nut (2) from idler pulley bracket (4) and discard
wheel. Replace with new pulley wheel (1).

NOTE

The pulley wheel bearings can not be replaced separately.

2

1

sm00302

1.

Axle

2.

Pinch bolt

Figure 5-42. Rear Axle

IDLER PULLEY INSTALLATION

1.

See

. Install new or existing pulley wheel (1),

if removed, and tighten washer and nut (2) to wheel
fastener (6) to 20-23 ft-lbs (27.1-31.2 Nm).

2.

Slide idler pulley bracket (4). Install washer and nuts (5)
on to studs (3) and tighten to 33-35 ft-lbs (44.7-47.5 Nm).
See

5.7 DRIVE BELT AND IDLER PULLEY, Drive Belt

.

3.

Install front sprocket cover. See

2.36 SPROCKET COVER

4.

Apply LOCTITE 271 (red) and install chin fairing fasteners.
Tighten to 36-48 in-lbs (4-5.4 Nm). See

.

NOTE

Never tighten rear axle with swingarm brace removed.

5.

. Install and tighten rear axle (1) to 23-27

ft-lbs (31.2-36.6 Nm), back off two full turns and then
retighten to 48-52 ft-lbs (65.1-70.5 Nm). See

2010 XB Service: Drive/Transmission 5-25

«
...
435
436
437
438
439
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: UNIT 1 Страницы: 23

Бренд: Kabuto Страницы: 16

Saddle Tramp BC-BTHBSP

Бренд: Metra Electronics Страницы: 8

Бренд: Suzuki Страницы: 42

Бренд: Yamaha Страницы: 220

Бренд: Yamaha Страницы: 402

Бренд: Yamaha Страницы: 402

Бренд: Yamaha Страницы: 176

Бренд: DYNATEK Страницы: 12

BAR CLAMP MOUNT PRO

Бренд: SP CONNECT Страницы: 3

Бренд: Triumph Страницы: 126

BLITZ 9-13 Visor

Бренд: Fubag Страницы: 17

CYBERCHARGER 50002

Бренд: Ciro Страницы: 3

Lectra VR24 1998

Бренд: EMB Страницы: 58

Бренд: MARLINK Страницы: 3

Бренд: B&G electronics Страницы: 5

Бренд: Kinroad Страницы: 28

Бренд: Kemimoto Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды