Buell XB 2010 Скачать руководство пользователя страница 374 | Manualshive

Страница: 374 / 714

background image

Connect positive (+) battery cable first. If positive (+) cable
should contact ground with negative (-) cable connected,
the resulting sparks can cause a battery explosion, which
could result in death or serious injury. (00068a)

3.

Connect battery positive cable (red) first, tightening to
60-70 in-lbs (6.8-7.9 Nm). See

1.16 BATTERY MAINTEN-

.

4.

Connect negative battery cable, tightening to 60-70 in-lbs
(6.8-7.9 Nm).

NOTE

If the ECM was replaced with a new component, it will be
necessary to download the correct calibration using D.T.
DIGITAL TECHNICIAN (Part No. HD-48650) and perform the
TPS zero procedure.

After installing seat, pull upward on seat to be sure it is
locked in position. While riding, a loose seat can shift
causing loss of control, which could result in death or
serious injury. (00070b)

5.

Install seat.

NOTES

•

The Throttle Position Sensor Zero Procedure should be
performed if the throttle position sensor or ECM have been
replaced or if the ECM has been recalibrated. See

4.5 THROTTLE POSITION SENSOR (TPS)

•

The throttle body has a throttle plate stop screw that is
preset at the factory and has tamper proof paint applied
to the head of the screw. Do NOT attempt to adjust this
screw. Tampering with this screw will require throttle body
replacement.

sm00857

Figure 4-7. Electronic Control Module (ECM): Lightning

(Typical)

sm00858

Figure 4-8. Electronic Control Module (ECM): Lightning

(XB12Ss)

ULYSSES

TOOL NAME

PART NUMBER

DIGITAL TECHNICIAN

HD-48650

Removal

1.

Remove seat.

Disconnect negative (-) battery cable first. If positive (+)
cable should contact ground with negative (-) cable con-
nected, the resulting sparks can cause a battery explosion,
which could result in death or serious injury. (00049a)

2.

Disconnect battery. See

1.16 BATTERY MAINTENANCE

3.

Disconnect ECM connector [10] and connector [11].

4.

Remove the two fasteners to detach electronic control
module from bracket.

NOTES

•

When removing the ECM, the fastener closest to the shock
assembly no longer has a nut that is captured in the plastic
shield below the ECM. The front fastener attaches directly
to the trunk pan. The rear fastener attaches directly to the
battery pan.

•

The fastener installed through the ECM and travel limiter
has a lockpatch and is to be used one time only. If
removed, always replace the front fastener with a new
one.

Installation

NOTE

Always install a new fastener with a lockpatch in front hole of
ECM closest to shock absorber.

1.

Align holes in ECM with those in electrical bracket. Install
rear fastener and tighten to 36-60 in-lbs (4-6.8 Nm).

2.

Install new front fastener and tighten to 30-40 in-lbs (3.4-
4.5 Nm).

4-8 2010 XB Service: Fuel System

«
...
372
373
374
375
376
...
»

Содержание XB 2010











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XB 2010

Бренд: Yamaha Страницы: 860

F 850 GS Adventure 2019

Бренд: BMW Motorrad Страницы: 346

Бренд: GAS GAS Страницы: 142

Бренд: GAS GAS Страницы: 34

Бренд: BMW Страницы: 19

Бренд: hepco & becker Страницы: 2

Бренд: hepco & becker Страницы: 4

Бренд: Arai Страницы: 15

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 24

Бренд: Yamaha Страницы: 61

Бренд: Yamaha Страницы: 78

Бренд: Yamaha Страницы: 79

Бренд: Yamaha Страницы: 94

Бренд: Yamaha Страницы: 90

Бренд: Yamaha Страницы: 86

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды