
2007 Buell P3: Chassis
2-21
INSTALLATION
1
1
WARNING
1
WARNING
Only install original equipment tire valves and valve
caps. A valve, or valve and cap combination, that is too
long or too heavy can strike adjacent components and
damage the valve, causing rapid tire deflation. Rapid tire
deflation can cause loss of vehicle control, which could
result in death or serious injury. (00281a)
1
1
WARNING
1
WARNING
Dunlop front and rear tires for Buell motorcycles are not
the same. They are not interchangeable. Use front tire
ONLY for a front tire. DO NOT put a rear tire on the front
of a vehicle. Failure to follow this warning could result in
death or serious injury.
NOTES
●
The red circle on the sidewall is a balance mark and
should be located next to the valve stem hole.
●
Leaving the valve core out of the valve stem will allow a
sufficient volume of air to inflate the radial tire to seat the
beads on the rim.
1.
Damaged or leaking valve stems must be replaced.
Place rubber grommet on valve stem with shoulder in
recess of the valve stem head.
2.
Install and tighten nut to 42-44 in-lbs (4.7-5.0 Nm).
3.
Thoroughly lubricate bead on both sides of tire with a
rubber lubricant. Lubricate inside diameter of bead and
side wall. Lubricate rim flanges and safety hump on
wheel.
1
1
WARNING
1
WARNING
Read the operating manual for the manufacturer and
model of tire machine used. Failure to follow operational
procedures or to heed any cautions/warnings in the man-
ual for the tire machine could result in death or serious
injury. (00283a)
4.
With rim installed in pneumatic tire machine jaws, orient
tire with rotational arrow pointing in direction of forward
rotation. Push one side off bottom bead into rim well and
walk the bottom bead around until it is completely in the
rim well.
5.
See
Starting at the valve stem, start first
bead into the rim well using a tire machine. If no machine
is available, work bead on as far as possible by hand.
Use a tire tool to pry the remaining bead over rim flange.
1
1
WARNING
1
WARNING
Do not use excessive force when starting bead over rim.
Excessive force may damage tire or rim and adversely
affect handling which could result in death or serious
injury.
6.
Position red dot at valve stem and starting 180 degrees
opposite valve stem, mount top bead to shoe of pneu-
matic tire machine.
7.
Rotate wheel to pull bead into rim well. Remove wheel
from tire machine.
1
1
WARNING
1
WARNING
Do not exceed manufacturer's recommended pressure to
seat beads. Exceeding recommended bead seat pres-
sure can cause tire rim assembly to burst, which could
result in death or serious injury. (00282a)
8.
Apply air to stem to seat beads on rim. It may be neces-
sary to use a TIRE BEAD EXPANDER (Part No. HD-
28700) on the tire until beads seal on rim.
Figure 2-22. Starting Bead on Rim (Typical)
a0209x2x
Содержание P3
