Buehler 11-2180 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 37

Buehler 11-2180 Скачать руководство пользователя страница 9

Activating the IsoMet

®

1000 Precision Saw

To activate power to the IsoMet

®

1000 Precision Saw flip the power switch on the back of

the machine to the UP position.

The IsoMet

®

1000 power switch is also a two-pole circuit breaker that will provide

protection for the machine in the event of an overload.

If at any time the Front Control Panel buttons or the motor does not operate, reset the
IsoMet

®

1000 by flipping the power switch to the DOWN position then back to the UP

position.

Blade Installation

1. Remove the thumbscrew, end cap bushing, and outer flange from the arbor shaft

(see

Figure 2

).

2. Install the blade on the arbor shaft against the inner flange.

3. Slide the outer flange, the end cap bushing, and the thumbscrew on to the arbor

shaft.

4. Hand tightened the thumbscrew to secure the blade.

Inner Flange

Blade

Arbor Shaft

Outer Flange

End Cap Bushing

Thumbscrew

Figure 2

Blade Installation

9

MA112180_33

6/27/2005

«
...
7
8
9
10
11
...
»

Содержание 11-2180






































Отзывы:

Нет отзывов