Buehler 11-2180 Скачать руководство пользователя страница 8

Страница: 8 / 37

Installation

CAUTION! Equipment Damage.

Follow all locally approved procedures and safety

practices when lifting and installing this machine. Improper lifting can result in machine
damage.

Select a location for your IsoMet

1000 Precision Saw that provides an adequate working space

and a power source.

The IsoMet

1000 Precision Saw is 15 ½ inches (394 mm) wide, 21 inches (533 mm) deep, and

12 inches (305 mm) high. Placement of the IsoMet

1000 Precision Saw should be on a sturdy,

level bench. Buehler TECH-MET

tables are highly recommended.

Allow 6 inches (150 mm) of space at the back of the IsoMet

1000 Precision Saw for raising the

hood. Make sure to leave sufficient space on both sides for sectioning long bars.

Electrical Installation

WARNING! Electrical Shock Hazard. Do not change the power plug in

any

way

. Buehler machines are equipped with a polarized plug (one blade is wider

than the other) and a ground pin. Polarized plugs reduce the risk of electrical
shock. This plug will fit in a polarized outlet only one way.

Check that Specification Plate values for voltage, current, and power consumption are
compatible with the intended electrical supply before installation.

The IsoMet

1000 Precision Saw can be plugged into an outlet rated for the voltage and

frequency listed on the Specification Plate.

WARNING! Electrical Shock Hazard.

A qualified electrical technician should

perform electrical maintenance.

•

Disconnect the power supply before making any electrical adjustments.

•

Capacitors inside the machine may retain a charge even if the machine
is disconnected from the power supply.

•

Installation of the IsoMet

1000 Precision Saw must comply with local

electrical standards or codes of practice.

IsoMet

1000 Precision Saw

Voltage / Frequency

11-2180

85 – 264 Volts / 50 – 60 Hz

Table 1

IsoMet

1000 Electrical Data

MA112180_33

6/27/2005

Содержание 11-2180






































Результаты поиска

Содержание 11-2180

Отзывы:

Buehler 11-2180, Руководство пользователя, Страница: 8 / 37

Результаты поиска

Содержание 11-2180

Отзывы: