background image

Tips on energy-efficient heating

3

 Logamatic 4121, 4122 and 4126 - Subject to technical modifications.

10

3

Tips on energy-efficient heating

Here are a few tips on how to heat economically, without 
sacrificing convenience:

z

Only heat if you need warmth. Utilise the preset 
heating programs (standard programs) in the control 
unit, or those that have been tailored to your 
individual requirements.

z

Air rooms correctly during the heating season: 
Open windows three to four times a day for 
approximately 5 minutes. Having the window slightly 
open all the time does not provide an air change and 
wastes valuable energy.

z

Close the thermostatic valves whilst ventilating.

z

Windows and doors are places where a lot of heat 
is lost. Therefore, check whether the doors and 
windows are correctly sealed. Shut your roller 
shutters (if installed) at night. 

z

Never position large objects such as a sofa or a desk 
immediately in front of radiators (minimum clearance 
50 cm). Otherwise, the heated air cannot circulate 
and heat the room adequately.

z

In rooms you occupy during the day, you can, for 
example, set a room temperature of 21 °C, whilst 
17 °C may be sufficient at night. To achieve this, 
use the standard heating mode (day mode) and the 
setback mode (night mode, 

Æ

 Chapter 6).

z

Never overheat rooms; overheated rooms are 
unhealthy, plus they waste money and energy. If you 
reduce the day room temperature, for example from 
21 °C to 20 °C, you can save approximately six 
percent of your heating bill. 

z

Also heat in an energy-conscious manner in spring 
and autumn, and utilise the summer/winter time 
changeover (

Æ

 Chapter 7).

z

A pleasant room climate not only depends on the 
room temperature, but also on the relative humidity. 
The drier the air, the cooler a room feels. You can 
optimise the relative humidity with house plants.

z

You can also save money when heating DHW: Only 
operate the DHW circulation pump via a time switch. 
Research has shown that it is generally sufficient to 
run the DHW circulation pump for only three minutes 
every half hour.

z

Arrange for your local heating contractor to service 
your heating system annually.

Содержание Logamatic 4121

























































































Отзывы: