POWERING ON
1. Slide the ‘ON/OFF’ toggle switch at the rear of the Alarm
Clock to the to the ‘ON’ position. Once turned on, the display
will show the time, clock icon, battery level and alarm icon,
if an alarm has been set.
2. Slide the toggle back to the ‘OFF’ position to turn
the poweroff to your Alarm Clock.
VOLUME
The default volume level in all modes is set at 10. The Alarm
Clock volume level ranges from 1 to a maximum volume of 15.
Increase volume by holding down the ‘Next’ button.
Decrease the volume by holding the ‘Previous’ button.
CHARGING ALARM CLOCK
1. Insert the micro-USB end of the included cable into
the 5V DC charging port on the back of the alarm clock.
Insert the opposite USB end if the cable into a
USB power source.
2. The red LED charging indicator will flash while charging
and stop flashing once the battery is fully charged.
3. When the battery level is lower than 20%, a low battery
prompt will sound and Alarm Clock functionality will be
limited to time display only in order to conserve battery.
SETTING THE TIME
1. Hold down the ‘Mode’ button until the hour flashes to enter
the ‘Clock’ setting.
2. Use the ‘Up’ and ‘Down’ buttons to set the correct hour.
3. Press the ‘Mode’ button and the minutes will flash.
4. Use the ‘Up’ and ‘Down’ buttons to set the correct minutes.
5. Press the ‘Mode’ button and the 24-hour or AM/PM
icon will flash.
6. Use the ‘Up’ and ‘Down’ buttons to change between
either 24 and 12 hour settings.
7. Hold down the ‘Mode’ button to save your settings.
ALARM SETTING
1. Press the ‘Mode’ ONCE button to set the first alarm.
2. Hold down the ‘Mode’ button again to enter
the Alarm setting mode, the hours will flash.
3. Use the ‘Up’ and ‘Down’ buttons to set the Alarm hour.
4. Press the ‘Mode’ button again, the minutes will flash.
5. Use the ‘Up’ and ‘Down’ buttons to set the minutes.
6. Press the ‘Mode’ button to select your alarm tone from
the five available options.
7. Press the ‘Mode’ button to choose between ‘ON’ or ‘OFF’.
8. Press the ‘Mode’ Button to select the number of alarms.
9. Hold down the ‘Mode’ button to save your settings.
Press the ‘Mode’ button TWICE to set the second alarm.
Repeate steps 1-9 to set the second alarm.
SNOOZING THE ALARM
Press any button to snooze your alarm. The alarm will
snooze for five minutes, then sound again. Double press
the ‘Snooze / Dimming’ button to turn off the alarm. Alarms can
be put on snooze three times before they turn off completely.
BLUETOOTH
®
PAIRING
1.Ensure the Alarm Clock is turned on by switching the rear
toggle to ‘ON’ position.
2. Hold down the
Bluetooth
ON/OFF button to enter
Bluetooth mode.
3. The Alarm Clock will sound with the
Bluetooth
tone
and begin searching for nearby devices.
4. Select
BD-ALMCLK-1
from the list of
Bluetooth
devices
on your laptop, smartphone or tablet. (Refer to your device
manual for help finding
Bluetooth
settings.)
5. Once connected, audio from your device can be played
through your Alarm Clock
Bluetooth
Speaker.
TF MEMORY CARD MODE
1.Hold down Bluetooth ON/OFF button then insert your TF
card into the TF slot at the rear of your Alarm Clock. It will
automatically switch to TF card mode and begin to play.
2. Press ‘Previous’ or ‘Next’ buttons to navigate through back
or forward between songs.
3. Pull out your TF card and the Alarm Clock will automatically
exit TF card mode and return to
Bluetooth
mode.
AUX AUDIO MODE
1. Ensure that your 3.5mm AUX audio cable is correctly
connected to your laptop, smartphone or tablet.
2.Connect the opposite end of the cable to the AUX input jack
on the rear of the clock, the clock will automatically enter AUX
audio mode.
3. When the 3.5mm AUX audio cable is disconnected
the Alarm Clock will automatically exit AUX mode and return
to
Bluetooth
mode.
FM RADIO MODE
1. Insert the micro-USB charging cable into the micro-USB
charging port to act as an antenna.
2. Hold down the ‘Play / Pause / Call / FM’ button to
enter FM mode.
3. Press the ‘Play / Pause / Call / FM’ button to enter
auto search mode.
4. Use the ‘Next’ and ‘Previous’ buttons to switch between
radio stations.
5. Hold down ‘Previous’ or ‘Next’ buttons to increase or
decrease the volume.
CHARGE DEVICE FROM USB
1. Insert the USB end of your USB charging cable into
the USB charge port at the rear of the Alarm Clock.
2. Insert the opposite end of your USB charging cable
into the respective charging port of your device and look
for the charging icon on your device to show charging
has commenced.
3. Your device will draw power from the Alarm Clocks
inbuilt battery if the Alarm Clock is not also plugged into
a USB power source.
TECHNICAL SPECIFICATIONS
Input: 5V DC 500mA-1A
Output: 5W x 2
Signal to Noise Ratio: ≥75dB
FM Frequency: 87.5 - 108MHz
Frequency: 60Hz - 20KHz
AUX : 3.5mm audio jack
Battery: Lithium ion, 2400mAh, 3.7V
Bluetooth
®
version: 4.2
Size: 185x48x72 mm
