BTT Melmak Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 28

BTT Melmak Скачать руководство пользователя страница 7

1

Introduction

The Melmak Device is a Low Intensity Pulsed Ultrasound Device (LIPUS). LIPUS devices have been
clinically found to support and accelerate the healing process of fresh fractures and non-unions.

The Melmak Device is intended for non-invasive use only, and should only be used as prescribed by
a physician or other health professional for its intended use.

Treatment is carried out for 20 minutes, once a day. Patients should treat themselves at approxi-
mately the same time each day.

1.1 Indications and Intended Use

The Melmak Device is indicated for the treatment of fresh
bone fractures and established non-unions excluding
treatment of the skull and the vertebral column. The loca-
tion and type of fracture will influence results.

This non-invasive treatment can only be prescribed by a
physician or other health professional.

1.2 Use with Internal Fixation

The Melmak Device can be used in the presence of metal
screws and plates.

1.3 Contraindications

There are no known contraindications to the use of the

Melmak Device.

01

INTRODUCTION

«
...
5
6
7
8
9
...
»

Содержание Melmak





























Отзывы:

Нет отзывов