manualshive.com logo in svg

BTM Lance-N-Loc, Руководство пользователя

Поделиться
Скачать
BTM Lance-N-Loc Скачать руководство пользователя страница 6

3.0 ConTInUeD

5. The booster is shipped with oil in the reservoir.  If the oil level is low, oil is added by removing the

plug at the top of the booster.  The oil level should reach the bottom thread of the booster cap.  Oil

should be properly handled, and disposed of.

Oil Level

Remove plug to

add oil

6.  Connect your air line to the booster.  BTM recommends that the system operates at 80 PSI (5.5 Bar).

Clean, dry air should be used.  The removal of air supply is required before tool change or service.

7. Press the trigger on the gun and dry cycle the unit.  If the unit fails to cycle, air needs to be bled
from the system.  See section 4 on bleeding the gun.

Unit requirements:

Recommended Air Pressure: 

80 PSI (5.5 Bar)

BTM recommends that clean, dry air is used.

Maximum Air Pressure: 

90 PSI (6.2 Bar)

Recommended Oil:

Amoco AW 32 to DTE 26 or any equivalent, non-foaming oil.

Oil should be handled and disposed of properly.

sT

aRT

 U

P P

R

o

Cee

DUR

e

Содержание Lance-N-Loc













Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды