21
ENGLISH
3. Ensure the bit is properly engaged.
NOTE:
The bit needs to move several centimeters in and out
of the tool holder
7
when properly engaged.
To remove the bit, pull back the locking sleeve and pull the
bit out.
Bit Position Adjustment
Turn the mode selector to bit adjustment icon (Refer to
Mode
Selection
) to adjust the chisel to the desired position. There are
multiple positions to set the angle of the chisel.
NOTE:
After finding the desired position, slightly maneuver
the chisel bit back and forth to ensure the chisel is
properly engaged.
OPERATION
Instructions for Use
WARNING:
Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Proper Hand Position (Fig. D)
WARNING:
To reduce the risk of serious personal injury,
ALWAYS
use proper hand position as shown.
WARNING:
To reduce the risk of serious personal
injury,
ALWAYS
hold securely in anticipation of
a sudden reaction.
Proper hand position requires one hand on the mounted side
handle, with the other hand on the main handle.
Mode Selection (Fig. E)
WARNING:
Do not select the operating mode when the
tool is running. Tool must come to a complete stop before
activating the mode selector button or damage to the tool
may result.
Your tool is equipped with a mode selector dial
4
to select the
mode appropriate to desired operation.
Symbol
Mode
Application
Bit
Adjustment
Chisel bit position adjustment
Hammering/
Chipping
Light chipping, chiseling
and demolition
To select a mode:
1. Depress the mode selector release button
5
.
2. Rotate the mode selector dial so that the arrow points to the
symbol corresponding for the desired mode.
NOTE:
The arrow on the mode selector dial
4
must be pointing
at a mode symbol at all times. There are no operable positions
in between.
Performing an Application (Fig. A, E)
WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS
ensure workpiece is anchored or
clamped firmly.
NOTE:
Operating temperature of this tool is 7 to +40 °C. Using
the tool outside of this temperature range will decrease the life
of the tool.
1. Insert the appropriate chisel and rotate it by hand to lock it
into the desired position. Refer to
Bit and Bit Holder
.
2. Using the mode selector dial
4
, select chipping mode.
Refer
to
Mode Selection
.
3. Adjust the side handle
2
as necessary. Refer to
Mounting
the Straight Side Handle
.
4. Place the bit/chisel on the desired location.
5. Depress the trigger switch
1
.
6. To stop the hammer, release the switch.
MAINTENANCE
Your BTI power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories.
Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Lubrication
Your power tool requires no additional lubrication.
Cleaning
WARNING:
Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING:
Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories
WARNING:
Since accessories, other than those offered by
BTI, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce
the risk of injury, only BTI recommended accessories
should be used with this product.
Содержание 9090150
Страница 1: ...www de MH 5 BOX Chissel hammer Art 9090150 ...
Страница 3: ...3 Fig A Fig B Fig C 1 6 2 3 4 5 7 8 3 2 9 7 8 9 ...
Страница 4: ...4 Fig E Fig D 5 4 ...
