background image

 
   

 

  BS33 

 

Remarks: Due to our policy of continual product development, we reserve the right to amend the specifications of the mentioned 

products without notice

 

 

10 

7.  LOW BATTERY INDICATION 

If the battery voltage is low, the “BAT “ enunciator will illuminate at the top right corner of the 
display. The battery should be changed immediately to ensure function and accuracy is 
according to the specification. Only alkaline 9volt battery should be used. 
 

8.  MEASURING RESISTANCE 

1.  If measuring wire resistance, follow steps 1 through 3 under Chapter 5 “Measuring Length 

of Wire” to connect wire. If a discrete resistor is being measured, perform the calibration 
procedure in the “

” position. 

2.  Read the resistance value directly from the display. 
 

9.  OPERATIONAL HINTS 

• 

Never apply voltage to the inputs. 

• 

Temperature affects readings. Allow the meter to attain the ambient temperature as the 
wire under test. 

• 

The sample length of user wires for the User Select Mode must be 5m in METER or 20ft 
in FEET mode. 

• 

The Listing label on the bottom of the holster enables users to make a short memo of 
each user wire for the User Select Mode. 

• 

Use a 9volt alkaline battery only. 

• 

If the meter wad turned on and inactivate for approximately 15 minutes, the meter will 
automatically enter into Sleep mode and displays “----“.    Reactivate the meter by turning 
the selector to any position or pressing any button. 

• 

Use the test leads that come with the meter only. Other test leads may not work. 

• 

Ensure that the test leads are clean and in good working order. 

• 

Ensure the wire under test is clean and free of oxidation. 

• 

Ensure that the alligator clips are connected across the diameter of the wire under test. 

Содержание BS33













Отзывы: