background image

Safety

2016-10-28 / DIS 820_58300000190984_ara_en_c

Copyright by BSH Hausgeräte GmbH

Page 4 of 17

2.1

Qualification

In Germany, only qualified electricians trained by BSH or an authorised body may

perform any repair work.
In other countries, only similarly trained qualified personnel is permitted to perform

the repair work.
Appliances must only be repaired by persons that are qualified, 

approved

 and

trained by BSH or an authorised body as instructed.

2.2

General safety information

2.2.1

All domestic appliances

Risk of electric shock due to live parts!

Disconnect the appliance from the mains for at least 60 seconds before starting

work.

Do not touch the housing, components and cables.

For tests on an energised system, use a residual current circuit breaker.

Discharge high-voltage capacitors.

Risk of injury from sharp edges!

Wear protective gloves.

Risk of injury when dealing with harmful substances!

Observe the associated safety data sheet!

Risk to the appliance's safety / function!

Only use original spare parts.

Risk of damage to electrostatically sensitive components (ESDs)!

Before touching ESDs, use an electrostatic protection system (wristband with

earth safe plug).

Do not touch connections and conductor paths of the modules.

Only transport ESDs in conductive materials or original packaging.

Keep ESDs clear of electrostatically chargeable materials (i.e. plastic).

Содержание PKM975DK1D


















Отзывы: