bSeen X E-bike Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 26

background image

INSTALLATION - FRONT LED UNITS CABLE PLACEMENT

The front LED units are mounted on the front fork - one on each side of it.

As you did on the previous step for the rear LED units, peel the double

tape and stick the LED unit in place.

Run the LED units’ cables along the brake lines to the place where you will

be fitting the ECU, using cable ties to fix them along the line.

Left LED Unit

Right LED Unit

«
...
9
10
11
12
13
...
»

Содержание X E-bike



























Отзывы:

Нет отзывов

Похожие инструкции для X E-bike

Бренд: Zetkama Страницы: 6

Бренд: Facility Explorer Страницы: 4

Бренд: IBM Страницы: 144

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: LAE electronic Страницы: 7

Бренд: LAE electronic Страницы: 2

Бренд: nekos Страницы: 8

Бренд: nekos Страницы: 8

Бренд: Neles Страницы: 12

Бренд: Pando Страницы: 43

Бренд: Watlow Страницы: 59

Tekmar WiFi Snow Melting Control 670

Бренд: Watts Страницы: 48

Бренд: Nemesis Страницы: 6

Бренд: Scanreco Страницы: 10

Бренд: Teledyne Страницы: 102

Бренд: Rain Bird Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды