background image

INTRODUCTION 

Thank you for choosing the 

D65/130/250Z Eight Channel Power Amplifier

. Bryston welcomes any suggestions you may 

have, or comments regarding the operation of your amplifier.  We consider you, our customer, to be Bryston’s most impor-

tant  resource, and your opinion is very much appreciated. 

DESCRIPTION

The 

D65/130/250Z

 are modular multi-channel audio power amplifiers of 65, 130 or 250 Watts/channel into 4Ω.  While 

each of the eight channels in the 

D65/130/250Z

 can operate completely independently, with its own input, output and level 

control, each channel is also assigned to one of 4 

Zones. 

 Each Zone is comprised of two adjacent channels and each 

zone can be remotely muted independently of the other zones.  Each channel can select from its own discrete input (RCA 

or phono jack) or from a common stereo input (stereo bus inputs, also RCA or phono jacks).  The inputs are single ended 

with a gain of 29dB. 

The 

power up sequence

 of the 

D65/130/250Z

 may be controlled from a 4 to 12v (AC or DC) control voltage.  The 

D65/130/250Z

 uses ‘soft start’ power control circuitry to eliminate high inrush currents when A/C power is applied. 

SHIPPING BOX & PACKING MATERIAL 

Please keep the original shipping box and all packing material. This will ensure the amplifier is protected in future transport.  

In the unlikely event you have a problem and must return it for service you

 must

 use the proper packing material as your 

unit may not be insurable the carrier if it is not shipped in the original packing material.

INSTALLATION & VENTILATION  

The most important installation consideration is 

ventilation

. The D65/130/250Z

 

amplifiers are onvection cooled. 

Unrestricted air-flow across its heat sinks is a must. For this reason do not install anything directly above it.  Allow at least 

3.5” inches (2u) of space above, 1.75 inches (1u) of space below and at least 1 inch to either side of this amplifier. Do 

not install directly above other heat generating equipment. If installed in a cabinet it should have an open front and back.  

Should your installation conditions be constricted, then additional forced air-cooling may be necessary. Any D65/130/250Z 

channels thermally shutting down during operation indicates insufficient cooling and a remedy must be found for cooling 

the amplifier. Provide a minimum 6” space to the rear of the D65/130/250Z

 

for ventilation and dressing cables to and from 

the amplifier. 

Never operate the 

D65/130/250Z

 in a vertical position

WIRING THE D65/130/250Z

  

(also see rear panel description )

S

peaker wires

 should be as short as practical. Use quality wire, and if runs are more than 3 meters use at least 12 gauge 

wire. The speaker binding posts will accept wire up to 3 gauge in size. Bryston can custom build cables for your application.

AC POWER

Before plugging in the power cord be sure your D65/130/250Z is specified for the 

correct A/C voltage

 for your locality. 

The voltage is listed by the power input connector. Never lift the safety ground to the amplifier or remove the ground pin 

from the plug.

AC POWER CONDITIONERS

Bryston urges caution in choosing a power conditioner for your audio/video system. Large power amplifiers can draw very 

substantial current from the wall plug, and many so-called power conditioners can in fact hinder the supply of current by 

inserting resistances in series with the line cord. However, there are now power conditioners that can reduce or eliminate 

RF and 'hash' from the AC supply and may actually improve current delivery to your system.  This type of power conditioner 

(exemplified by Bryston 

B•I•T

 Power Conditioners) uses the energy storage in a large toroidal tranformer to provide high 

instantaneous power and reduce the substantial AC output resistance of the wall socket and house wiring. This resistance 

can be in the range of 0.5 to 1 Ohm and is typically reduced to only a few milliOhms by the Power Conditioner. That in turn 

considerably reduces Voltage drop in the power line on high current surges and quite substantially increases the stability 

of the power line improving audio (and video) focus, precision and clarity.

D65Z 

 D130Z 

 D250Z 

 

8 CHANNEL POWER AMPLIFIERS    

Содержание D65Z









Отзывы: