background image

BRYSTON 20 -YEAR WARRANTY

Bryston products are warranted to be free from
manufacturing defects for a minimum of twenty
years from the original date of manufacture. This
includes parts, labour and return shipping to the
first owner and all subsequent owners. Warranty
coverage is automatic and commences with the
original date of manufacture which is kept on file
at Bryston.

In the event of a defect or malfunction, Bryston
will remedy the problem by repair or replacement,
as we deem necessary, to restore the product to
full performance. 

This warranty is considered void if the defect,
malfunction or failure of the product or any com-
ponent part was caused by damage ( not resulting
from a defect or malfunction ) or  abuse  while in
the possession of the customer. Tampering by
persons other than factory authorized service
personnel, or  failure to fully comply with Bryston
operating instructions, voids the warranty.

This warranty gives you specific legal rights and
you may also have other rights which may vary
from province to province and country to country.

BRYSTON LTD.
P.O. BOX 2170
677 NEAL DRIVE
PETERBOROUGH, ONTARIO
CANADA 
K9J 7Y4

FOR BRYSTON SERVICE OUTSIDE CANADA:

CONTACT YOUR LOCAL DISTRIBUTOR

OR 

CHECK OUR WEB SITE AT: [email protected] 

OR

CALL BRYSTON DIRECTLY AT: 

PHONE: 705-742-5325

FAX: 705-742-0882

BRYSTON SERVICE U.S.A.:

70 COVENTRY ST.

SUITE #5

NEWPORT VERMONT. 

U.S.A. 05855

PHONE: 802- 334-1201

FAX: 802-334-6658

BRYSTON SERVICE CANADA:

24 STEINWAY BLVD., UNIT 48

ETOBICOKE, ONTARIO

CANADA  M9W 6T8

PHONE: 416-675-2585

FAX: 416-675-3103

Содержание 9BSST-THX

















Отзывы: