manualshive.com logo in svg

Brymen BM905, Руководство пользователя

Поделиться
Скачать
Brymen BM905 Скачать руководство пользователя страница 14

 

13 

Battery and Fuse replacement 
Battery use:   

Standard 1.5V AAA Size (NEDA 24A or IEC LR03) battery X 2 

Fuses use: 

Fuse (FS1) for 

AmA current input:   

0.4A

/1000V ac & dc, IR 30kA, F fuse, or better; Dimension: 6 x 32 mm 

Fuse (FS2) for A current input:   

11A/1000V ac & dc, IR 20kA, F fuse, or better; Dimension: 10 x 38 mm 

 
Battery  replacement for models with 
battery access door: 
Loosen  the  2  screws  from  the 
battery  access  door  of  the  case 
bottom.  Lift  the  battery  access  door 
and  thus  the  battery  compartment 
up.  Replace  the  battery.  Re-fasten 
the screws. 
 
Fuse  replacement  (and  also  Battery 
replacement for splash proof version 
without battery access door): 
Loosen  the  4  screws  from  the  case 
bottom.  Lift  the  end  of  the  case 
bottom nearest the input jacks until it 
unsnaps from the case top. Replace 
the blown fuse(s) and/or the battery. 
Replace  the  case  bottom,  and 
ensure  that  all  the  gaskets  are 
properly  seated  and  the  two  snaps 
on the case top (near the LCD side) 
are engaged. Re-fasten the screws. 

 

Содержание BM905





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды