background image

3

UNIT FALLING HAZARD

Failure to follow this warning could result in personal injury

or death.
Never stand beneath rigged units or lift over people.

!

WARNING

PROPERTY DAMAGE HAZARD

Failure to follow this warning could result in personal

injury/death or property damage.

Rigging brackets for one unit use only.

When removing a

unit at the end of its useful life, use a new set of brackets.

!

WARNING

USE OF RIGGING BRACKET

Field Installation of Rigging Bracket (if not already

installed)

1. Remove unit from shipping carton. Leave top shipping skid

on the unit for use as a spreader bar to prevent the rigging
straps from damaging the unit. If the skid is not available, use

a spreader bar of sufficient length to protect the unit from
damage.

2. Remove 4 screws in unit corner posts.
3. Attach each of the 4 metal rigging brackets under the panel

rain lip. Use the screws removed in step 2 above to secure the

brackets to the unit.

PROPERTY DAMAGE HAZARD

Failure to follow this warning could result in personal

injury/death or property damage.
Rigging bracket MUST be under the rain lip to provide

adequate lifting.

!

WARNING

PROPERTY DAMAGE HAZARD

Failure to follow this warning could result in personal

injury/death or property damage.
Do not strip screws when re--securing the unit. If a screw is

stripped, replace the stripped one with a larger diameter screw

(included). When straps are taut, the clevis should be a

minimum of 36 in. (914 mm) above the unit top cover.

!

WARNING

Rigging/Lifting of Unit

1. Bend top of brackets down approximately 30 degrees from the

corner posts.

2. Attach straps of equal length to the rigging brackets at

opposite ends of the unit. Be sure straps are rated to hold the
weight of the unit.

3. Attach a clevis of sufficient strength in the middle of the straps.

Adjust the clevis location to ensure unit is lifted level with the

ground.

4. Remove corner post screws and rigging brackets, then

re--install screws.

After the unit is placed on the roof curb or mounting pad, remove the

top crating.

607C

Содержание 607C024



























Отзывы: