Bryant 581J series Скачать руководство пользователя страница 44

Страница: 44 / 44

PRESSURES (CONT.)

VERIFY REFRIGERANT CHARGE USING CHARGING CHARTS

GENERAL

ECONOMIZER MINIMUM VENT AND CHANGEOVER SETTINGS TO JOB REQUIREMENTS (IF EQUIPPED)

VERIFY SMOKE DETECTOR UNIT SHUTDOWN BY UTILIZING MAGNET TEST

III. PERFECT HUMIDITY

SYSTEM START-UP

STEPS

1. CHECK CTB FOR JUMPER 5, 6, 7

JUMPER 5, 6, 7 MUST BE CUT AND OPEN

2. OPEN HUMIDISTAT CONTACTS

3. START UNIT IN COOLING (CLOSE Y1)

OBSERVE AND RECORD

A. SUCTION PRESSURE

PSIG

B. DISCHARGE PRESSURE

PSIG

C. ENTERING AIR TEMPERATURE

D. LIQUID LINE TEMPERATURE

AT OUTLET OR REHEAT COIL

E. CONFIRM CORRECT ROTATION FOR COMPRESSOR

F. CHECK FOR CORRECT RAMP−UP OF OUTDOOR FAN MOTOR AS CONDENSER COIL WARMS

4. CHECK UNIT CHARGE PER CHARGING CHART

5. SWITCH UNIT TO HIGH−LATENT MODE (SUBCOOLER) BY CLOSING HUMIDISTAT WITH Y1 CLOSED

OBSERVE

A. REDUCTION IN SUCTION PRESSURE (5 TO 7 PSI EXPECTED)

B. DISCHARGE PRESSURE UNCHANGED

C. LIQUID TEMPERATURE DROPS TO 50 TO 55

F RANGE

D. LIQUID SOLENOID VALVE (LSV) ENERGIZED (VALVE CLOSES)

6. SWITCH UNIT TO DEHUMID (REHEAT) BY OPENING Y1

OBSERVE

A. SUCTION PRESSURE INCREASES TO NORMAL COOLING LEVEL

B. DISCHARGE PRESSURE DECREASES (35 TO 50 PSI)

C. LIQUID TEMPERATURE RETURNS TO NORMAL COOLING LEVEL

D. LIQUID SOLENOID VALVE (LSV) ENERGIZED (VALVE CLOSES)

DISCHARGE SOLENOID VALVE (DSV) ENERGIZED, VALVE OPENS

7. WITH UNIT IN DEHUMID MODE CLOSE W1

COMPRESSOR AND OUTDOOR FAN STOP; LSV AND DSV SOLENOIDS DE−ENERGIZED

8. OPEN W1 RESTORE UNIT TO DEHUMID MODE

9. OPEN HUMIDISTAT INPUT

COMPRESSOR AND OUTDOOR FAN STOP; LSV AND DSV SOLENOIDS DE−ENERGIZED

10. RESTORE SETPOINTS FOR THERMOSTAT AND HUMIDISTAT

REPEAT PROCESS FOR 2 COMPRESSOR SYSTEMS

Edition Date: 09/16 11-16A

Printed in U.S.A.

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

Catalog No: II581J-7-12-02

Replaces: II581J-7-12-01

581J

Содержание 581J series













































Результаты поиска

Содержание 581J series

Отзывы:

Похожие инструкции для 581J series

Бренды по названию

Популярные бренды

Bryant 581J series, Руководство по установке

Результаты поиска

Содержание 581J series

Отзывы:

Похожие инструкции для 581J series

Бренды по названию

Популярные бренды