Bryant 580J*04A Скачать руководство пользователя страница 47

Страница: 47 / 52

Fig. 65 — EconoMi$er

IV Wiring

Step 13 — Adjust Factory-Installed Options

SMOKE DETECTORS —

Smoke detector(s) will be con-

nected at the Controls Connections Board, at terminals marked

“Smoke Shutdown”. Cut jumper JMP 3 when ready to ener-

gize unit.

ECONOMI$ER IV OCCUPANCY SWITCH —

Refer to

Fig. 65 for general EconoMi$er IV wiring. External occupancy

control is managed through a connection on the Controls Con-

nections Board.

If external occupancy control is desired, connect a time

clock or remotely controlled switch (closed for Occupied, open

for Unoccupied sequence) at terminals marked OCCUPANCY.

Cut jumper JMP 2 to complete the installation.

Step 14 — Install Accessories

Available accessories include:

• Curb

• Thru-base connection kit (must be installed before unit is

set on curb)

• LP conversion kit

• Flue discharge deflector

• Manual outside air damper

• Two-Position motorized outside air damper

• EconoMi$er IV (with control)

• EconoMi$er 2 (without control/for external signal)

• Power Exhaust

• Differential dry-bulb sensor (EconoMi$er IV)

• Outdoor enthalpy sensor

• Differential enthalpy sensor

• CO

sensor

• Louvered hail guard

• Phase monitor control

Refer to separate installation instructions for information on

installing these accessories.

Step 15 — Check Belt Tension —

Measure the belt

span length as shown in Fig. 66. Calculate the required deflec-

tion by multiplying the belt span length by

. For example, if

the belt span length is 32 inches: 32 x

inch deflection.

BELT FORCE — DEFLECTION METHOD —

Check

the belt tension with a spring-force belt force deflection gauge

(available from drive belt manufacturer).

1. Place a straightedge along the belt between the two

pulleys. Measure the distance between the motor shaft
and the blower shaft.

2. Set the tension gauge to the desired tension (see Table 1

in Fig. 66). Place the large O-ring at that point.

3. Press the tension checker downward on the belt until the

large O-ring is at the bottom of the straightedge.

4. Adjust the belt tension as needed.

Содержание 580J*04A





















































Результаты поиска

Содержание 580J*04A

Отзывы:

Бренды по названию

Популярные бренды

Bryant 580J*04A, Руководство по установке

Результаты поиска

Содержание 580J*04A

Отзывы:

Бренды по названию

Популярные бренды