Bryant 580J*04A Скачать руководство пользователя страница 48

Страница: 48 / 52

Adjust belt tension by loosing the motor mounting plate

front bolts and rear bolt (see Fig. 67) and slide the plate to-

wards the fan (to reduce tension) or away from the fan (to in-

crease tension). Ensure the blower shaft and motor shaft are

parallel to each other (pulleys aligned). Tighten all bolts se-

curely when finished.

BELT TENSION METHOD —

Requires belt tension

gauge that measures tension in belt in units of lbs force.

Fig. 66 — V-Belt Force Label

Fig. 67 — Belt Drive Motor Mounting

Pre-Start and Start-Up —

This completes the mechani-

cal installation of the unit. Refer to the unit’s Service Manual

for detailed Pre-Start and Start-Up instructions. Download the

latest versions from HVAC Partners (www.hvacpartners.com).

Table 1

Table 2

BELT

CROSS

SECTION

SMALLEST

SHEAVE

DIAMETER

BELT DEFLECTION FORCE (LBS)

UNNOTCHED

BELTS

NOTCHED BELTS

USED

NEW

USED

NEW

A, AX

3.0-3.6

3.7

5.5

4.1

6.1

3.8-4.8

4.5

6.8

5.0

7.4

5.0-7.0

5.4

8.0

5.7

8.4

B, BX

3.4-4.2

—

4.9

7.2

4.4-5.6

5.3

7.9

7.1

10.5

5.8-8.6

6.3

9.4

8.5

12.6

BELT CONDITION

TENSION FORCE IN BELT (LBS)

New

100

Used

BLOWER PULLEY

V-BELT

MOTOR

PULLEY

MOTOR

MOTOR MOUNTING

PLATE

MOUNTING

BOLTS (4)

Содержание 580J*04A





















































Результаты поиска

Содержание 580J*04A

Отзывы:

Бренды по названию

Популярные бренды

Bryant 580J*04A, Руководство по установке

Результаты поиска

Содержание 580J*04A

Отзывы:

Бренды по названию

Популярные бренды