Bryant 575Jx08G/H Series Скачать руководство пользователя страница 20

Страница: 20 / 40

If the outdoor coil’s Defrost Thermostat switch (DFT) is

closed (shorting DFB terminals DFT1 and DFT1), the

Defrost cycle will start. Output at OF is removed; outdoor

fans stop during the Defrost cycle. Output P3–7 (RVS1) is

energized; reversing valve solenoid RVS is energized and

reversing valve changes position, placing the circuit in a

Cooling mode flow, directing hot gas into the outdoor coil

where its heat melts the frost and loosens the ice on the

coil face.

During the Defrost cycle, output EHEAT is also energized (if

not already energized by a thermostat W2 demand);

supplemental heater will be energized. During the Defrost

Cycle, LED1 on the DFB will be illuminated. The Defrost

cycle ends when DFT opens (as liquid temperature exiting

the coil rises above DFT setpoint) or the defrost cycle runs

for 10 minutes. Output at EHEAT is removed; supplemental

heater will be de-energized (unless thermostat has a W2

demand). Output at OF is restored; outdoor fans start again.

Output P3–7 (RVS1) is removed; reversing valve returns to

Heating position.

Defrost cycle is fixed at a maximum 10 minute duration

limit. The period to test and initiate a Defrost cycle can be

configured for 30, 60, 90 or 120 minutes.

Supplemental Heat/Emergency Heat —

Supplemental heat type is determined by 524J indoor unit

options and accessories. This heat is initiated when the

indoor unit W2 terminal is energized by the thermostat. (Or

as detailed in “Defrost Cycle” above.) The thermostat may

energize W2 as supplemental (2nd stage) heat at higher

space heating demand, or when selected as emergency heat

mode. When the space heating demand decreases below the

2nd stage limit, or emergency heat is turned off, W2 is

de-energized, and supplemental heat is turned off.

Cooling and Heating Shutdown —

Partial or complete cooling or heating functions may

shutdown caused by loss of main power, open pressure

switches, diagnostic alarms, or open internal compressor

protections. See Service section for further details.

ROUTINE SYSTEM MAINTENANCE

These items should be part of a routine maintenance

program, to be checked every month or two, until a specific

schedule for each can be identified for this installation:

Quarterly Inspection

(and 30 days after initial start) —

Indoor section

Coil cleanliness checked.

Return air filter replacement

Belt tension checked

Belt condition checked

Pulley alignment checked

Fan shaft bearing locking collar tightness checked

Condensate drain checked

Blower motor amperage

Outdoor Section

Fan motor mounting bolts tightness

Compressor mounting bolts

Fan blade positioning

Control box cleanliness and wiring condition

Wire terminal tightness

Refrigerant charge level

Economizer or Outside Air Damper

Inlet filters condition

Check damper travel (economizer)

Check gear and dampers for debris and dirt

575J

*08G/

Содержание 575Jx08G/H Series









































Результаты поиска

Содержание 575Jx08G/H Series

Отзывы:

Бренды по названию

Популярные бренды

Bryant 575Jx08G/H Series, Инструкция по установке, запуску и обслуживанию

Результаты поиска

Содержание 575Jx08G/H Series

Отзывы:

Бренды по названию

Популярные бренды