Bryant 558J Series Скачать руководство пользователя

Страница: 15 / 44

Field Control Wiring —

The 558J unit requires an external temperature control

device. This device can be a thermostat emulation device

provided as part of a third--party Building Management

System.

Thermostat —

Select a Bryant--approved accessory thermostat. When

electric heat is installed in the 558J unit, the thermostat

must be capable of energizing the G terminal (to energize

the Indoor Fan Contactor) whenever there is a space call

for heat (energizing the W1 terminal). The accessory

thermostats listed on the unit price pages can provide this

signal but they are not configured to enable this signal as

shipped.

Install the accessory thermostat according to installation

instructions included with the accessory.

Locate the thermostat accessory on a solid wall in the

conditioned space to sense average temperature in

accordance with the thermostat installation instructions.
If the thermostat contains a logic circuit requiring 24--v

power, use a thermostat cable or equivalent single leads of

different colors with minimum of seven leads. If the

thermostat does not require a 24--v source (no “C”

connection required), use a thermostat cable or equivalent

with minimum of six leads. Check the thermostat

installation instructions for additional features which

might require additional conductors in the cable.
For wire runs up to 50 ft. (15 m), use no. 18 AWG

(American Wire Gage) insulated wire [35

C (95

minimum]. For 50 to 75 ft. (15 to 23 m), use no. 16 AWG

insulated wire [35

C (95

F) minimum]. For over 75 ft.

(23 m), use no. 14 AWG insulated wire [35

C (95

minimum]. All wire sizes larger than no. 18 AWG cannot

be directly connected to the thermostat and will require a

junction box and splice at the thermostat.

O/B/Y2

Ttypical
Thermostat
Corrections

T
H
E
R
M
O
S
T
A
T

(Note 1)

(Note 2)

(Note 3)

Note 1: Typical multi-function marking. Follow manufacturer’s configuration

instructions to select Y2.

Note 2: Y2 to Y2 connection required on single-stage cooling units when

integrated economizer function is desired

Note 3: W2 connection not required on units with single-stage heating.

Field Wiring

Central

Terminal

Board

C08575

Fig. 21 -- Low--Voltage Connections

Unit without Thru--Base Connection Kit —

Pass the thermostat control wires through the hole

provided in the corner post; then feed the wires through

the raceway built into the corner post to the control box.

Pull the wires over to the terminal strip on the upper--left

corner of the Controls Connection Board. See Fig. 22.

RACEWAY

HOLE IN END PANEL (HIDDEN)

C08027

Fig. 22 -- Field Control Wiring Raceway

NOTE

If thru--the--bottom connections accessory is

used, refer to the accessory installation instructions for
information on routing power and control wiring.

Heat Anticipator Settings —

Set heat anticipator settings at 0.14 amp for the first stage

and 0.14 amp for second--stage heating, when available.

Electric Heaters

558J units may be equipped with field--installed accessory

electric heaters. The heaters are modular in design, with

heater frames holding open coil resistance wires strung

through ceramic insulators, line--break limit switches and

a control contactor. One or two heater modules may be

used in a unit.
Heater modules are installed in the compartment below

the indoor (supply) fan outlet. Access is through the

indoor access panel. Heater modules slide into the

compartment on tracks along the bottom of the heater

opening. See Fig. 23, Fig. 24 and Fig. 25.
Not all available heater modules may be used in every

unit. Use only those heater modules that are UL listed for

use in a specific size unit. Refer to the label on the unit

cabinet for the list of approved heaters.
Unit heaters are marked with Heater Model Numbers. But

heaters are ordered as and shipped in cartons marked with

a corresponding heater Sales Package part number. See

Table 2 for correlation between heater Model Number and

Sales Package part number.

NOTE

: The value in position 9 of the part number differs

between the sales package part number (value is 1) and a
bare heater model number (value is 0).

558J

Содержание 558J Series













































Результаты поиска

Содержание 558J Series

Отзывы:

Похожие инструкции для 558J Series

Бренды по названию

Популярные бренды

Bryant 558J Series, Руководство по установке

Результаты поиска

Содержание 558J Series

Отзывы:

Похожие инструкции для 558J Series

Бренды по названию

Популярные бренды