Bryan Boilers FREE FLEX Скачать руководство пользователя страница 7

Страница: 7 / 100

Bryan Steam, LLC

www.bryanboilers.com

Phone: 765-473-6651

783 N Chili Ave, Peru, IN 46970 [email protected]

Test and Inspections

Upon the completion of boiler installation, final air-

fuel adjustments are to be made by factory trained

service personnel. The emissions data and the O2

levels at minimum and maximum input rate can be

found on the back side of the front-boiler’s door,

which can be referenced in the future by the boiler

operator(s) when troubleshooting and servicing the

boiler. In addition, the following tests and inspections

are made on each boiler at the factory to ensure it

meets our highest safety and functionality standards.

•

ASME hydrostatic test inspection

•

Electrical components inspection

•

Operating & efficiency test

•

Final engineering inspection

•

Crating inspection

DANGER

DO NOT store or use gasoline or other flammable

vapors or liquids in the vicinity of this or any other

appliance.
If you smell gas vapors, DO NOT try to operate any

appliance—DO NOT touch any electrical switch or

use any phone in the building. Immediately, call the

gas supplier from a remotely located phone. Follow

the gas supplier’s instructions or if the supplier is

unavailable, contact the fire department.

Component Description

(

See Figure 1, Figure 2 and Figure 3

)

E. Touchscreen display.

The display provides easy access for viewing

and adjusting boiler operational parameters,

monitoring historical performance characteristics and

annunciating boiler alarm/lockout conditions.

1. Boiler On/Off switch.

2. Manual gas shutoff valve. The boiler is

equipped with two manual gas shut off valves,

one located on the incoming gas supply line

outside of the boiler, and the other downstream

of the main gas valve.

3. Main gas supply connection.
4. Pressure relief valve. The pressure relief

protects the heat exchanger from an over-

pressure condition.

5. Ducted combustion air flange.
6. Flue gas vent outlet. The boiler comes with

a standard AL 29-4C® stainless steel vent

connection.

7. Boiler water flow switch. The boiler water

flow switch is adjustable within the parameters

listed in Table 1. (

Located inside the boiler on

Free Flex 1500 - Free Flex 6000

)

Table 1: Water Flow Switch Settings

Settings

Mode Of Operation

Switch Closed

Switch Open

Minimum

Maximum

8. Return water connection. A 3” diameter

Victaulic grooved connection is provided on

the Free Flex 1000. A 3”, 150# class, flange is

provided on the Free Flex 1500 – 3000. A 6”,

150# class, flange is provided on the Free Flex

3500-6000.

9. Clean out and inspection. The Free Flex 1000

has a 3” diameter Victaulic grooved connection

is provided for inspecting and cleaning sediment

from the heat exchanger. The Free Flex 1500-

6000 has a 1” NPT pipe for blow down to clean

sediment from the heat exchanger and a 3”

removable plug for inspecting.

10. Supply water connection. A 3” diameter

Victaulic grooved connection is provided on

the Free Flex 1000. A 3”, 150# class, flange

is provide on the Free Flex 1500 – 3000. A 6”,

150# class, flange is provided on the Free Flex

3500-6000.

Содержание FREE FLEX





































































































Результаты поиска

Содержание FREE FLEX

Отзывы:

Bryan Boilers FREE FLEX, Руководство по установке и эксплуатации, Страница: 7 / 100

Результаты поиска

Содержание FREE FLEX

Отзывы: